LIMITED WARRANTY

The Company warrants the products it manufactures against defects in materials and workmanship

for a period limited to two years from the date of shipment, provided the products have been stored,

handled, installed, and used under proper conditions. The Company’s liability under this limited

warranty shall extend only to the repair or replacement of a defective product, at The Company’s

option. The Company disclaims all liability for any affirmation, promise or representation with

respect to the products.

The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against

damages, claims, and expenses arising out of subsequent sales of RLC products or products

containing components manufactured by RLC and based upon personal injuries, deaths, property

damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be

to any extent liable, including without limitation penalties imposed by the Consumer Product Safety

Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty

Act (P.L. 93-637), as now in effect or as amended hereafter.

No warranties expressed or implied are created with respect to The Company’s products except those

expressly contained herein. The Customer acknowledges the disclaimers and limitations contained

herein and relies on no other warranties or affirmations.

The Length Sensor Hinge Clamp Assembly provides an easy method for

attachment and mounting of the Length Sensors and LSCB1 Conversion

Bracket. The removable top on the solid zinc LSAHC mounting block

allows quick installation of the Length Sensor handle tube and provides

secure clamping retention. The mounting block pivots freely in zinc right

angle brackets to allow mounting the assembly via clearance holes for 1/4"

dia. bolts.

The lock washers must be used as indicated (between the bolt head and

the top clamp piece). Assemble the top clamp piece as follows.

1. Tighten both bolts so that the top clamp half draws down evenly on

the sensor tube.

2. Tighten the bolts until both lock washers are flat.

ORDERING INFORMATION

.88

(22.4)

2.9

(73.7)

3.4

(86.4)

2.5 (63.5)

1.25

(31.8)

.25 (6.3)

Lock washers (2) must be

installed between bolt heads

and top clamp piece.

E-clip retaining ring (2)

must be installed in slots.

5.70 (144.8)

4.50 (114.3)

(50.8)

(38.1)

0.75

0.75 (19.0)

4X Ø 0.31 (7.9)

2.00

1.50

(19.0)

SINGLE WHEEL

2.93 (74.4)

DUAL WHEEL 4 (101.6)

(21.6)

.85

.88 (22.4)

WHEEL

RADIUS

1.9

(48.3)

6.9

(175.3)

FRONT

VIEW

TOP

VIEW

DIMENSIONS In inches (mm)

CAUTION: Downward tension

on signal cable can cause

wheel(s) to lift. Make sure

cable is clamped to

machine frame near

encoder and allow slack.

NOTE: The weight at the

Length Sensor unit

provides sufficient traction

for accurate operation

when mounted as shown,

with arm angle from

horizontal not exceeding

±30°, and with hinge clamp

toward the far extreme of

the extension arm.

Length Sensors should be mounted so measuring

wheel(s) contact ribbon, strip or web as it passes over

a roller. As an alternative, wheel(s) can be driven by

roller surface next to material being measured.

MODEL NO.

DESCRIPTION

PART NUMBER

LSAHC

LSAHC001

Length Sensor Hinge Clamp Assembly

MODEL LSAHC - LENGTH SENSOR HINGE CLAMP ASSEMBLY

Model ZGG Shown

Model ZFG Shown

Red Lion Controls

Headquarters

20 Willow Springs Circle

York PA 17406

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

Red Lion Controls

China

Unit 101, XinAn Plaza

Building 13, No.99 Tianzhou Road

ShangHai, P.R. China 200223

Tel +86 21 6113-3688

Fax +86 21 6113-3683

Red Lion Controls

Europe

Printerweg 10

NL - 3821 AD Amersfoort

Tel +31 (0) 334 723 225

Fax +31 (0) 334 893 793

Red Lion Controls

India

54, Vishvas Tenement

GST Road, New Ranip,

Ahmedabad-382480 Gujarat, India

Tel +91 987 954 0503

Fax +91 79 275 31 350