Motore di ricerca datesheet componenti elettronici |
|
Si8642BA-C-IU Scheda tecnica(PDF) 6 Page - Silicon Laboratories |
|
Si8642BA-C-IU Scheda tecnica(HTML) 6 Page - Silicon Laboratories |
6 / 42 page 3. Device Operation Device behavior during start-up, normal operation, and shutdown is shown in Figure 3.1 Device Behavior during Normal Operation on page 7, where UVLO+ and UVLO– are the respective positive-going and negative-going thresholds. Refer to the following tables to determine outputs when power supply (VDD) is not present and for logic conditions when enable pins are used. Table 3.1. Si86xx Logic Operation VI Input1, 2 EN Input1, 2, 3, 4 VDDI State1, 5, 6 VDDO State1, 5, 6 VO Output1, 2 Comments H H or NC P P H Enabled, normal operation. L H or NC P P L X7 L P P Hi-Z8 Disabled. X7 H or NC UP P L9 H9 Upon transition of VDDI from unpowered to powered, VO returns to the same state as VI in less than 1 µs. X7 L UP P Hi-Z8 Disabled. X7 X7 P UP Undetermined Upon transition of VDDO from unpowered to powered, VO returns to the same state as VI within 1 µs, if EN is in either the H or NC state. Upon transition of VDDO from unpow- ered to powered, VO returns to Hi-Z within 1 µs if EN is L. Note: 1. VDDI and VDDO are the input and output power supplies. VI and VO are the respective input and output terminals. EN is the enable control input located on the same output side. 2. X = not applicable; H = Logic High; L = Logic Low; Hi-Z = High Impedance. 3. It is recommended that the enable inputs be connected to an external logic high or low level when the Si86xx is operating in noisy environments. 4. No Connect (NC) replaces EN1 on Si8640/45. No Connect replaces EN2 on the Si8645. No Connects are not internally connec- ted and can be left floating, tied to VDD, or tied to GND. 5. “Powered” state (P) is defined as 2.5 V < VDD < 5.5 V. 6. “Unpowered” state (UP) is defined as VDD = 0 V. 7. Note that an I/O can power the die for a given side through an internal diode if its source has adequate current. 8. When using the enable pin (EN) function, the output pin state is driven into a high-impedance state when the EN pin is disabled (EN = 0). 9. See 1. Ordering Guide for details. This is the selectable fail-safe operating mode (ordering option). Some devices have default output state = H, and some have default output state = L, depending on the ordering part number (OPN). For default high devi- ces, the data channels have pull-ups on inputs/outputs. For default low devices, the data channels have pull-downs on inputs/ outputs. Si864x Data Sheet Device Operation silabs.com | Smart. Connected. Energy-friendly. Rev. 2.0 | 5 |
Codice articolo simile - Si8642BA-C-IU |
|
Descrizione simile - Si8642BA-C-IU |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |