Motore di ricerca datesheet componenti elettronici
  Italian  ▼
ALLDATASHEETIT.COM

X  

2--1490413--1 Scheda tecnica(PDF) 3 Page - TE Connectivity Ltd

Il numero della parte 2--1490413--1
Spiegazioni elettronici  Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
Download  5 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Produttore elettronici  TEC [TE Connectivity Ltd]
Homepage  http://www.te.com/usa-en/home.html
Logo TEC - TE Connectivity Ltd

2--1490413--1 Scheda tecnica(HTML) 3 Page - TE Connectivity Ltd

  2--1490413--1 Datasheet HTML 1Page - TE Connectivity Ltd 2--1490413--1 Datasheet HTML 2Page - TE Connectivity Ltd 2--1490413--1 Datasheet HTML 3Page - TE Connectivity Ltd 2--1490413--1 Datasheet HTML 4Page - TE Connectivity Ltd 2--1490413--1 Datasheet HTML 5Page - TE Connectivity Ltd  
Zoom Inzoom in Zoom Outzoom out
 3 / 5 page
background image
408- 10110
3
of 5
Rev D
3. Insert the stripped wire into the wire barrel of the
terminal or splice making sure that the end of the
wire is visible through the sight hole.
4. Center the terminal or splice in the nest as
shown in Figure 4.
To avoid personal injury, make sure to exercise
caution when holding terminals, splices, or wire
near the crimping area.
Figure 4
Terminal or Splice
Centered in Nest
(See Detail)
Sight Hole
Facing Nest
Wire Visible
Through
Sight Hole
Nest
Indenter
Indenter
Nest
Wire Visible
Through
Sight Hole
Terminal
Splice
Detail
Sight Hole
Facing Nest
5. Activate the head or tool according to the
instructions included with the head or tool so that
ram advances and holds the terminal or splice in
place. DO NOT deform the wire barrel.
6. For terminals, insert the stripped wire into the
wire barrel until the end of the conductor is visible
in the sight hole. For butt splices, insert a stripped
wire into the wire barrel until the end of the
conductor is visible in the sight hole.
7. Activate the head or tool to crimp the wire
barrel.
If the terminal or splice sticks in the die after
crimping, grasp the wire close to the crimp and
apply a rocking motion to remove it from the die.
8. For splices, insert a stripped wire into the
uncrimped wire barrel until the end of the
conductor is visible in the sight hole.
9. Inspect the crimp according to Figure 5. This is
included as an aid to the tool operator ONLY. It is
not intended to serve as a quality control
inspection for qualifying finished crimps on these
terminals and splices. Use only terminals or splices
that meet the conditions shown in the ACCEPT
column. Terminals and splices displaying the
features shown in the REJECT column can be
avoided by careful use of these instructions and by
performing the maintenance and inspection
procedures described in Section 5.
Damaged terminals or splices should not be
used. If a damage is evident, the terminal or
splice should be cut from the wire and replaced
with a new one. DO NOT re--terminate terminals
or splices.
5. MAINTENANCE AND INSPECTION
To avoid personal injury, DISCONNECT THE
POWER SUPPLY before performing
maintenance, adjustments, inspection, or repair.
5.1. Daily Maintenance
It is recommended that each operator of the dies be
made aware of, and responsible for, the following
steps of daily maintenance:
1. Remove dust, moisture, and other contaminants
from the dies with a clean brush, or a clean, soft,
lint--free cloth. DO NOT use objects that could
damage the dies.
2. If dies are coated with oil or preservative, wipe
them clean—particularly in the crimping
areas—before placing them in use.
3. When dies are not in use, make certain all
surfaces are protected with a THIN coat of any
good SAE 20 motor oil, then mate and store them
in a clean, dry area.
5.2. Periodic Inspection
Periodic inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the dies or be made available to
personnel responsible for the dies. Though
recommendations call for at least a monthly
inspection, the inspection frequency should be based
upon the amount of use, working conditions, operator
training and skill, and established company
standards. These inspections should be performed in
the following sequence.
A. Visual Inspection
1. Remove all lubrication and accumulated film by
immersing the dies in a suitable degreaser that will
not affect paint or plastic.
DANGER
NOTE
i
CAUTION
!
DANGER


Codice articolo simile - 2--1490413--1

Produttore elettroniciIl numero della parteScheda tecnicaSpiegazioni elettronici
logo
TE Connectivity Ltd
2--21000--0 TEC-2--21000--0 Datasheet
115Kb / 4P
   Base Assembly Universal
2--21000--3 TEC-2--21000--3 Datasheet
210Kb / 7P
   Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
2--21000--3 TEC-2--21000--3 Datasheet
115Kb / 4P
   Base Assembly Universal
logo
Tyco Electronics
2--21000--5 MACOM-2--21000--5 Datasheet
108Kb / 4P
   0.8mm CHAMP* Crimper Assemblies
2--21000--6 MACOM-2--21000--6 Datasheet
108Kb / 4P
   0.8mm CHAMP* Crimper Assemblies
More results

Descrizione simile - 2--1490413--1

Produttore elettroniciIl numero della parteScheda tecnicaSpiegazioni elettronici
logo
Tyco Electronics
408-10324 MACOM-408-10324 Datasheet
239Kb / 5P
   Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools
408-9935 MACOM-408-9935 Datasheet
247Kb / 6P
   Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
logo
TE Connectivity Ltd
408-9359 TEC-408-9359 Datasheet
210Kb / 7P
   Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
logo
Tyco Electronics
408-9039 MACOM-408-9039 Datasheet
103Kb / 5P
   Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools
411-3236 MACOM-411-3236 Datasheet
216Kb / 5P
   Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
logo
TE Connectivity Ltd
408-6561 TEC-408-6561 Datasheet
110Kb / 4P
   Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
408-1216 TEC-408-1216 Datasheet
91Kb / 2P
   Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools
logo
Tyco Electronics
408-8377 MACOM-408-8377 Datasheet
249Kb / 6P
   Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools
408-8607 MACOM-408-8607 Datasheet
247Kb / 6P
   Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
408-9240 MACOM-408-9240 Datasheet
85Kb / 3P
   Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
More results


Html Pages

1 2 3 4 5


Scheda tecnica Scarica

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEETIT.COM
Lei ha avuto il aiuto da alldatasheet?  [ DONATE ] 

Di alldatasheet   |   Richest di pubblicita   |   contatti   |   Privacy Policy   |   scambio Link   |   Ricerca produttore
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com