Motore di ricerca datesheet componenti elettronici |
|
2--1490413--0 Scheda tecnica(PDF) 3 Page - TE Connectivity Ltd |
|
2--1490413--0 Scheda tecnica(HTML) 3 Page - TE Connectivity Ltd |
3 / 5 page 408- 10110 3 of 5 Rev D 3. Insert the stripped wire into the wire barrel of the terminal or splice making sure that the end of the wire is visible through the sight hole. 4. Center the terminal or splice in the nest as shown in Figure 4. To avoid personal injury, make sure to exercise caution when holding terminals, splices, or wire near the crimping area. Figure 4 Terminal or Splice Centered in Nest (See Detail) Sight Hole Facing Nest Wire Visible Through Sight Hole Nest Indenter Indenter Nest Wire Visible Through Sight Hole Terminal Splice Detail Sight Hole Facing Nest 5. Activate the head or tool according to the instructions included with the head or tool so that ram advances and holds the terminal or splice in place. DO NOT deform the wire barrel. 6. For terminals, insert the stripped wire into the wire barrel until the end of the conductor is visible in the sight hole. For butt splices, insert a stripped wire into the wire barrel until the end of the conductor is visible in the sight hole. 7. Activate the head or tool to crimp the wire barrel. If the terminal or splice sticks in the die after crimping, grasp the wire close to the crimp and apply a rocking motion to remove it from the die. 8. For splices, insert a stripped wire into the uncrimped wire barrel until the end of the conductor is visible in the sight hole. 9. Inspect the crimp according to Figure 5. This is included as an aid to the tool operator ONLY. It is not intended to serve as a quality control inspection for qualifying finished crimps on these terminals and splices. Use only terminals or splices that meet the conditions shown in the ACCEPT column. Terminals and splices displaying the features shown in the REJECT column can be avoided by careful use of these instructions and by performing the maintenance and inspection procedures described in Section 5. Damaged terminals or splices should not be used. If a damage is evident, the terminal or splice should be cut from the wire and replaced with a new one. DO NOT re--terminate terminals or splices. 5. MAINTENANCE AND INSPECTION To avoid personal injury, DISCONNECT THE POWER SUPPLY before performing maintenance, adjustments, inspection, or repair. 5.1. Daily Maintenance It is recommended that each operator of the dies be made aware of, and responsible for, the following steps of daily maintenance: 1. Remove dust, moisture, and other contaminants from the dies with a clean brush, or a clean, soft, lint--free cloth. DO NOT use objects that could damage the dies. 2. If dies are coated with oil or preservative, wipe them clean—particularly in the crimping areas—before placing them in use. 3. When dies are not in use, make certain all surfaces are protected with a THIN coat of any good SAE 20 motor oil, then mate and store them in a clean, dry area. 5.2. Periodic Inspection Periodic inspections should be performed by quality control personnel. A record of scheduled inspections should remain with the dies or be made available to personnel responsible for the dies. Though recommendations call for at least a monthly inspection, the inspection frequency should be based upon the amount of use, working conditions, operator training and skill, and established company standards. These inspections should be performed in the following sequence. A. Visual Inspection 1. Remove all lubrication and accumulated film by immersing the dies in a suitable degreaser that will not affect paint or plastic. DANGER NOTE i CAUTION ! DANGER |
Codice articolo simile - 2--1490413--0 |
|
Descrizione simile - 2--1490413--0 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |