Motore di ricerca datesheet componenti elettronici |
|
2--1490413--0 Scheda tecnica(PDF) 2 Page - TE Connectivity Ltd |
|
2--1490413--0 Scheda tecnica(HTML) 2 Page - TE Connectivity Ltd |
2 / 5 page 408- 10110 Rev D 2 of 5 Figure 2 Upper Die Release Button Nest Indenter Lower Die Release Button Ram (Advanced) Stationary Die Release Button Moving Die Release Button Ram (Advanced) Nest Indenter Hydraulic Crimping Head Hydraulic Hand Crimping Tool “C” Head Yoke Yoke “C” Head To avoid personal injury, make sure to exercise extreme caution when using the head or tool. Avoid depressing the footswitch or trigger control when installing or removing the dies. 3.1. Die Installation 1. Depress the upper die release button (head) or stationary die release button (tool) located on the “C”--head. See Figure 2. 2. Slide the nest into place in the “C”--head. See Figure 2. 3. Release the button, and rock the nest back and forth until the nest snaps into position. 4. Activate the head or tool according to the instructions included with the head or tool until the lower die release button (head) or moving die release button (tool) located in the ram is exposed. Depress the button. 5. Slide the indenter into position in the ram. See Figure 2. 6. Release the button, and rock the indenter back and forth until the indenter snaps into position. 7. Return ram to the down position. 3.2. Die Removal 1. Depress the upper die release button (head) or stationary die release button (tool) located on the “C”--head, and slide the nest out. See Figure 2. 2. Activate the head or tool according to the instructions included with the head or tool until the lower die release button (head) or stationary die release button (tool) located in the ram is exposed. 3. Depress the button, and slide the indenter out of the ram. 4. CRIMPING PROCEDURE 1. Ensure that the wire range or size stamped on the terminal or splice corresponds with the wire size being used and the wire range or size marked on the nest and indenter. 2. Strip the wire to the dimension given in Figure 3. DO NOT nick or cut the wire strands. Insulation Strip Length (Refer to Table) Note: Not to Scale Conductors NOMINAL WIRE SIZE (AWG) STRIP LENGTH 8 11.43 [.450] 6 12.06 [.475] 4 13.34 [.525] 2 14.60 [.575] 1 15.87 [.625] 1/0 17 46 [ 688] 2/0 17.46 [.688] 3/0 19.05 [.750] 4/0 20.64 [.812] Figure 3 DANGER |
Codice articolo simile - 2--1490413--0 |
|
Descrizione simile - 2--1490413--0 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |