Motore di ricerca datesheet componenti elettronici
  Italian  ▼
ALLDATASHEETIT.COM

X  

1--21048--0 Scheda tecnica(PDF) 3 Page - Tyco Electronics

Il numero della parte 1--21048--0
Spiegazioni elettronici  Pneumatic Head Assembly
Download  5 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Produttore elettronici  MACOM [Tyco Electronics]
Homepage  http://www.macom.com
Logo MACOM - Tyco Electronics

1--21048--0 Scheda tecnica(HTML) 3 Page - Tyco Electronics

  1--21048--0 Datasheet HTML 1Page - Tyco Electronics 1--21048--0 Datasheet HTML 2Page - Tyco Electronics 1--21048--0 Datasheet HTML 3Page - Tyco Electronics 1--21048--0 Datasheet HTML 4Page - Tyco Electronics 1--21048--0 Datasheet HTML 5Page - Tyco Electronics  
Zoom Inzoom in Zoom Outzoom out
 3 / 5 page
background image
408--4070
Pneumatic Head Assembly 679304--1
3
of 5
Rev D
Tyco Electronics Corporation
Figure 3
Long Die Retaining
Screw
Short Die Retaining
Screw
Die Retaining Pin
Anvil Die
Chamfers of Die
Positioned Toward
Front of Head Assembly
Crimper Die
Bushings
Jaw
Hex Nut
Locator Assembly
Jaw
3. Connect the tool to an adequate air supply
(between 620 and 690 kPa [90 and100 psi]). For
specific information on air line requirements and air
hose installation, refer to the instructions packaged
with the pneumatic tooling assembly.
4. To remove the head assembly from the tool
holder, remove quick pins,then remove the head
assembly from tool holder.
3. CRIMPING PROCEDURE
The crimping procedures which follow are basic.
Refer to the instruction sheet packaged with the die
assembly for details.
ALWAYS keep fingers clear of head assembly
jaws when operating the pneumatic tooling
assembly.
1. Strip the wire using the recommended strip
length dimensions. Refer to instruction sheet
supplied with the die assembly.
2. Open the jaws of the head assembly by
squeezing the rollers together; then position the
connector into the appropriate crimping chamber.
3. After the connector is properly positioned in the
dies, release the rollers to allow the jaws to spring
shut, securing the connector within the dies.
4. Insert the stripped wire into the connector.
5. Activate the pneumatic tooling assembly to
complete the crimp. Open the jaws by squeezing
the rollers together, then remove the crimped
connector.
4. MAINTENANCE AND INSPECTION
ALWAYS disconnect the pneumatic tooling
assembly from the air supply before performing
any maintenance or inspection.
The head assembly is thoroughly inspected before
packaging. Since there is the possibility of damage
during shipment, new head assemblies should be
inspected immediately upon arrival at your facility.
DANGER
DANGER


Codice articolo simile - 1--21048--0

Produttore elettroniciIl numero della parteScheda tecnicaSpiegazioni elettronici
logo
Tyco Electronics
1--21046--3 MACOM-1--21046--3 Datasheet
94Kb / 3P
   Crimping Die Assemblies
More results

Descrizione simile - 1--21048--0

Produttore elettroniciIl numero della parteScheda tecnicaSpiegazioni elettronici
logo
TE Connectivity Ltd
408-8878 TEC-408-8878 Datasheet
217Kb / 4P
   626 Pneumatic Crimping Head 1490191-1 (Used with 626 Pneumatic Tooling Assemblies)
logo
Tyco Electronics
408-4198 MACOM-408-4198 Datasheet
378Kb / 6P
   This instruction sheet covers the application and maintenance procedures for Pneumatic Crimping Head Assembly
logo
TE Connectivity Ltd
408-6789 TEC-408-6789 Datasheet
268Kb / 5P
   Pistol Grip Pneumatic Handle Assembly
logo
Molex Electronics Ltd.
64007-7100 MOLEX11-64007-7100 Datasheet
29Kb / 1P
   Crimp Head for the AT-200 Pneumatic Hand Tool
0640056600 MOLEX11-0640056600 Datasheet
30Kb / 1P
   Crimp Head for the AT-200 Pneumatic Hand Tool
0640071200 MOLEX11-0640071200 Datasheet
29Kb / 1P
   Crimp Head for the AT-200 Pneumatic Hand Tool
0640050400 MOLEX11-0640050400 Datasheet
41Kb / 1P
   Crimp Head for the AT-200 Pneumatic Hand Tool
0640053600 MOLEX-0640053600 Datasheet
40Kb / 1P
   Crimp Head for the AT-200 Pneumatic Hand Tool
11/02/2021
0640054600 MOLEX-0640054600 Datasheet
40Kb / 1P
   Crimp Head for the AT-200 Pneumatic Hand Tool
11/02/2021
0640052100 MOLEX-0640052100 Datasheet
44Kb / 2P
   Crimp Head for the AT-200 Pneumatic Hand Tool
11/02/2021
More results


Html Pages

1 2 3 4 5


Scheda tecnica Scarica

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEETIT.COM
Lei ha avuto il aiuto da alldatasheet?  [ DONATE ] 

Di alldatasheet   |   Richest di pubblicita   |   contatti   |   Privacy Policy   |   scambio Link   |   Ricerca produttore
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com