 |
Motore di ricerca datesheet componenti elettronici |
|
|
Motore di ricerca datesheet componenti elettronici |
|
AM5716 Scheda tecnica(PDF) 11 Page - Texas Instruments |
|
|
||||||||||||||||||||||||||||||
AM5716 Scheda tecnica(HTML) 11 Page - Texas Instruments |
|
|
11 / 394 page  11 AM5718, AM5716 www.ti.com SPRS957C – MARCH 2016 – REVISED NOVEMBER 2016 Submit Documentation Feedback Terminal Configuration and Functions Copyright © 2016, Texas Instruments Incorporated NOTE In some cases Table 4-2 may present more than one signal name per muxmode for the same ball. First signal in the list is the dominant function as selected via CTRL_CORE_PAD_* register. All other signals are virtual functions that present alternate multiplexing options. This virtual functions are controlled via CTRL_CORE_ALT_SELECT_MUX or CTRL_CORE_VIP_MUX_SELECT register. For more information on how to use this options, please refer to Device TRM, Chapter Control Module, Section Pad Configuration Registers. 4. PN: This column shows if the functionality is applicable for AM5716 device. Note that the Ball Characteristics table presents a functionality of AM5718. If the cell is empty it means that the signal is available in all devices. - Yes - Functionality is presented in AM5716 - No - Functionality is not presented in AM5716 An empty box means Yes. 5. MUXMODE: Multiplexing mode number: (a) MUXMODE 0 is the primary mode; this means that when MUXMODE=0 is set, the function mapped on the pin corresponds to the name of the pin. The primary muxmode is not necessarily the default muxmode. NOTE The default mode is the mode at the release of the reset; also see the RESET REL. MUXMODE column. (b) MUXMODE 1 through 15 are possible muxmodes for alternate functions. On each pin, some muxmodes are effectively used for alternate functions, while some muxmodes are not used. Only MUXMODE values which correspond to defined functions should be used. 6. TYPE: Signal type and direction: – I = Input – O = Output – IO = Input or Output – D = Open drain – DS = Differential Signaling – A = Analog – PWR = Power – GND = Ground – CAP = LDO Capacitor 7. BALL RESET STATE: The state of the terminal at power-on reset: – drive 0 (OFF): The buffer drives VOL (pulldown or pullup resistor not activated). – drive 1 (OFF): The buffer drives VOH (pulldown or pullup resistor not activated). – OFF: High-impedance – PD: High-impedance with an active pulldown resistor – PU: High-impedance with an active pullup resistor 8. BALL RESET REL. STATE: The state of the terminal at the deactivation of the rstoutn signal (also mapped to the PRCM SYS_WARM_OUT_RST signal). – drive 0 (OFF): The buffer drives VOL (pulldown or pullup resistor not activated). – drive clk (OFF): The buffer drives a toggling clock (pulldown or pullup resistor not activated). – drive 1 (OFF): The buffer drives VOH (pulldown or pullup resistor not activated). – OFF: High-impedance – PD: High-impedance with an active pulldown resistor – PU: High-impedance with an active pullup resistor |
Codice articolo simile - AM5716 |
|
Descrizione simile - AM5716 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEETIT.COM |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Italian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
