Motore di ricerca datesheet componenti elettronici |
|
SN74F1056D Scheda tecnica(PDF) 3 Page - Texas Instruments |
|
|
SN74F1056D Scheda tecnica(HTML) 3 Page - Texas Instruments |
3 / 11 page SN74F1056 8-BIT SCHOTTKY BARRIER DIODE BUS-TERMINATION ARRAY SDFS085A – AUGUST 1992 – REVISED JULY 1997 3 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 APPLICATION INFORMATION Large negative transients occurring at the inputs of memory devices (DRAMs, SRAMs, EPROMs, etc.) or on the CLOCK lines of many clocked devices can result in improper operation of the devices. The SN74F1056 diode termination array helps suppress negative transients caused by transmission-line reflections, crosstalk, and switching noise. Diode terminations have several advantages when compared to resistor termination schemes. Split resistor or Thevenin equivalent termination can cause a substantial increase in power consumption. The use of a single resistor to ground to terminate a line usually results in degradation of the output high level, resulting in reduced noise immunity. Series damping resistors placed on the outputs of the driver reduce negative transients, but they also can increase propagation delays down the line, as a series resistor reduces the output drive capability of the driving device. Diode terminations have none of these drawbacks. The operation of the diode arrays in reducing negative transients is explained in the following figures. The diode conducts current when the voltage reaches a negative value large enough for the diode to turn on. Suppression of negative transients is tracked by the current-voltage characteristic curve for that diode. A typical current versus voltage plot for the SN74F1056 is shown in Figure 1. To illustrate how the diode arrays act to reduce negative transients at the end of a transmission line, the test setup in Figure 2(a) was evaluated. The resulting waveforms with and without the diode are shown in Figure 2(b). The maximum effectiveness of the diode arrays in suppressing negative transients occurs when the diode arrays are placed at the end of a line and/or the end of a long stub branching off a main transmission line. The diodes also can be used to reduce the negative transients that occur due to discontinuities in the middle of a line. An example of this is a slot in a backplane that is provided for an add-on card. VF – Forward Voltage – V Variable 1: VIN –Ch 1 Linear Sweep: Start 0.000 V Stop –2.000 V Step –0.010 V Constants: VHI –Vs1 3.5000 V VLO –Vs2 0.0000 V DIODE FORWARD CURRENT vs DIODE FORWARD VOLTAGE –50 –40 –20 –10 0 –90 –30 0 0.2 0.4 0.6 0.8 1 1.2 –70 –60 –80 –100 1.4 1.6 1.8 2 TA = 25°C Figure 1. Current Versus Voltage for the SN74F1056 |
Codice articolo simile - SN74F1056D |
|
Descrizione simile - SN74F1056D |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |