Motore di ricerca datesheet componenti elettronici |
|
ADC08351 Scheda tecnica(PDF) 5 Page - National Semiconductor (TI) |
|
|
ADC08351 Scheda tecnica(HTML) 5 Page - National Semiconductor (TI) |
5 / 15 page Converter Electrical Characteristics (Continued) The following specifications apply for V A =VD = +3.0 VDC,VREF = 2.4V, VIN = 1.63 VP-P, OE = 0V, CL = 20 pF, f CLK = 42 MHz, 50% duty cycle, unless otherwise specified. Boldface limits apply for T A =TMIN to TMAX: all other limits TA = 25˚C (Notes 7, 8) Symbol Parameter Conditions Typical (Note 9) Limits (Note 9) Units (Limits) Digital Output Characteristics I OH High Level Output Current V D = 2.7V, VOH =VD −0.5V −1.1 mA (min) I OL Low Level Output Current V D = 2.7V, OE = DGND, VOL = 0.4V 1.8 mA (min) V OH High Level Output Voltage V D = 2.7V, IOH = −360 µA 2.65 V V OL Low Level Output Voltage V D = 2.7V, IOL = 1.6 mA 0.2 V I OZH, I OZL TRI-STATE Output Current OE = V D = 3.3V, VOH = 3.3V or VOL =0V ±10 µA AC Electrical Characteristics f C1 Maximum Conversion Rate 42 MHz (min) f C2 Minimum Conversion Rate 2 MHz t OD Output Delay CLK High to Data Valid 14 19 ns (max) Pipline Delay (Latency) 2.5 Clock Cycles t DS Sampling (Aperture) Delay CLK Low to Acquisition of Data 2 ns t OH Output Hold Time CLK High to Data Invalid 9 ns t EN OE Low to Data Valid Loaded as in Figure 2 14 ns t DIS OE High to High Z State Loaded as in Figure 2 10 ns ENOB Effective Number of Bits f CLK = 30 MHz, fIN = 1 MHz 7.2 Bits f CLK = 42 MHz, fIN = 4.4 MHz 7.2 Bits f CLK = 42 MHz, fIN = 21 MHz 6.8 6.1 Bits (min) SINAD Signal-to-Noise & Distortion f CLK = 30 MHz, fIN = 1 MHz 45 dB f CLK = 42 MHz, fIN = 4.4 MHz 45 dB f CLK = 42 MHz, fIN = 21 MHz 43 38.5 dB (min) SNR Signal-to-Noise Ratio f CLK = 30 MHz, fIN = 1 MHz 44 dB f CLK = 42 MHz, fIN = 4.4 MHz 45 dB f CLK = 42 MHz, fIN = 21 MHz 44 41 dB (min) THD Total Harmonic Distortion f CLK = 30 MHz, fIN = 1 MHz −57 dB f CLK = 42 MHz, fIN = 4.4 MHz −51 dB f CLK = 42 MHz, fIN = 21 MHz −46 −41 dB (min) SFDR Spurious Free Dynamic Range f CLK = 30 MHz, fIN = 1 MHz 57 dB f CLK = 42 MHz, fIN = 4.4 MHz 54 dB f CLK = 42 MHz, fIN = 21 MHz 49 41 dB (min) Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is func- tional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed speci- fications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: All voltages are measured with respect to GND = AGND = DGND = 0V, unless otherwise specified. Note 3: When the input voltage at any pin exceeds the power supplies (that is, less than AGND or DGND, or greater than VA or VD), the current at that pin should be limited to 25 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 25 mA to two. Note 4: The absolute maximum junction temperature (TJmax) for this device is 150˚C. The maximum allowable power dissipation is dictated by TJmax, the junction-to-ambient thermal resistance ( θJA), and the ambient temperature (TA), and can be calculated using the formula PDMAX=(TJmax - TA)/θJA. For the 20-pin TSSOP, θJA is 135˚C/W, so PDMAX = 926 mW at 25˚C and 481 mW at the maximum operating ambient temperature of 85˚C. Note that the power dissipation of this device under normal operation will typically be about 68 mW (40 mW quiescent power + 23 mW reference ladder power+5mWdue to 1 TTL loan on each digital output). The values for maximum power dissipation listed above will be reached only when the ADC08351 is operated in a severe fault condition (e.g., when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided. Note 5: Human body model is 100 pF capacitor discharged through a 1.5 k Ω resistor. Machine model is 220 pF discharged through ZERO Ohms. Note 6: See AN-450, “Surface Mounting Methods and Their Effect on Product Reliability”, or the section entitled “Surface Mount” found in any post 1986 National Semiconductor Linear Data Book, for other methods of soldering surface mount devices. Note 7: All inputs are protected as shown below. Input voltage magnitudes up to 500 mV above the supply voltage or 500 mV below GND will not damage this device. However, errors in the A/D conversion can occur if the input goes above VA or below AGND by more than 300 mV. As an example, if VA is 3.0 VDC, the full-scale input voltage must be ≤3.3 VDC to ensure accurate conversions. www.national.com 5 |
Codice articolo simile - ADC08351 |
|
Descrizione simile - ADC08351 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |