Motore di ricerca datesheet componenti elettronici |
|
M02139-33 Scheda tecnica(PDF) 9 Page - M/A-COM Technology Solutions, Inc. |
|
M02139-33 Scheda tecnica(HTML) 9 Page - M/A-COM Technology Solutions, Inc. |
9 / 18 page Functional Description 02139-DSH-001-D Mindspeed Technologies ® 9 Mindspeed Proprietary and Confidential 3.2 General Description 3.2.1 TIA (Transimpedance Amplifier) The transimpedance amplifier consists of a high gain single-ended amplifier (TIA) with a feedback resistor. The feedback creates a virtual low impedance at the input and nearly all of the input current passes through the feedback resistor defining the voltage at the output. Advanced design techniques are employed to maintain the stability of this stage across all input conditions. An on-chip low dropout linear regulator has been incorporated into the design to give excellent noise rejection up to several MHz. The circuit is designed for PIN photodiodes with the anode connected to the input of the TIA and the cathode connected to AC ground, such as the provided PINK terminal. Reverse DC bias is applied to reduce the photodiode capacitance. PIN photodiodes and Avalanche photodiodes may also be connected externally to a voltage higher than VCC. Care should be taken to correctly sequence the power supply to the externally biased photodiode so that the bias voltage does not appear when the TIA is powered down. Doing so may cause damage to the input of the TIA, as the photodiode bias can become capacitively coupled to the PIN input, and cause damage. 3.2.2 Output Stage The signal from the TIA enters a phase splitter followed by a DC-shift stage and a pair of voltage follower outputs. These are designed to drive a differential (100 Ω) load. They are stable for driving capacitive loads such as interstage filters. Each output has its own GND pad; it is recommended but not required that all four GND pads on the chip should be connected. Since the M02139 exhibits rapid roll-off (3 pole), no external filtering is necessary. 3.2.3 Offset Cancellation DC Servo Due to the high gain of the M02139 transimpedance amplifier, any amount of input offset voltage would be amplified and create distortion at the output. Therefore, an offset cancellation circuit is used to remove input offset. The RC offset cancellation circuit sets the low frequency cutoff to 50 kHz. 3.2.4 Monitor O/P and Rate Select Between 1G and 10G Operations The monitor is a high impedance output which sources an average photodiode current for alignment or power monitoring use. This output is mirrored off the PINK current source, and PINK must be used to enable IMON usage. If PINK is not used as in the case of externally biased PIN or APD detectors, then photo current must be monitored via that external bias supply and the MON pin tied to high or low depending on the input data rate. This output is compatible with the DDMI Receive Power Specification (SFP-8472). An interfacing example is shown below where the M02139 is connected to the M0217x driver family General Purpose I/O (GPIO) and Rx Power monitoring A/D. Ensure that the voltage on VMON is in the range of 0 to 2.0 V. Refer to Table 3-1 and Figure 3-2. Table 3-1. Selection of Rm for Maximum Input Current IIN Max (mA) Optical Power (dBm) Rm ( Ω) 2+3 500 1 0 1000 0.5 -3 2000 |
Codice articolo simile - M02139-33 |
|
Descrizione simile - M02139-33 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |