Motore di ricerca datesheet componenti elettronici |
|
LC78615E Scheda tecnica(PDF) 9 Page - ON Semiconductor |
|
LC78615E Scheda tecnica(HTML) 9 Page - ON Semiconductor |
9 / 24 page LC78615E www.onsemi.com 9 Pin No. Pin name I/O State when “Reset” Function 54 CONT12 I/O Input(Low) General purpose I/O port with pull down resistor LR clock input for CD data (exclusive with CONT04 and CONT09) C2 error flag output for CD data Block synchronization signal (SBSY) output for CD subcode Data request signal input for CD-TEXT interface (exclusive with CONT04, CONT08 and CONT09) 55 CONT13 I/O Input(Low) General purpose I/O port with pull down resistor Bit clock output for CD data Bit clock input for CD data(exclusive with CONT05 and CONT10) Frame synchronization signal (SFSY) output for CD subcode Clock input/output for CD-TEXT interface (exclusive with CONT05 and CONT10) 56 CONT14 I/O Input(Low) General purpose I/O port with pull down resistor Serial data output for CD data PW data output in CD subcode Serial data output for CD-TEXT interface Watch Dog Timer state monitor output 57 MODE I Input LSI mode set input. This pin must be connected to the DVDD level. 58 DVDD15 AO High Capacitor connection pin for internal regulator 59 DVDD Digital system power supply 60 XVSS Oscillator ground. This pin must be connected to the 0V level. 61 XOUT O Oscillation 16.9344MHz oscillator connection 62 XIN I Oscillation 16.9344MHz oscillator connection 63 XVDD Oscillator power supply 64 SLCO AO Undefined Slice Level Control output <Notes> (1) For Unused pins : The unused input pins must be connected to the GND(0V) level if there is no individual note in the above table. The unused output pins must be left open(No connection) if there is no individual note in the above table. The unused input/output pins must be connected to the GND(0V) or power supply pin for I/O block with internal pull down/up resistor OFF or be left open with internal pull down/up resistor ON when input pin mode or must be left open(No connection ) when output pin mode if there is no individual note in the above table. When you connect an I/O pin which is an input pin without internal pull-down/up resistor at reset mode to the GND or power supply level, we recommend you to use pull-down resistor or pull-up resistor individually as fail-safe. (2) For Power supply pins : Same voltage level must be supplied to DVDD, AVDD, XVDD and VVDD1 power supply pins. (3) For “Reset” condition : This IC is not reset only by making the RESB pin “Low”. Refer to “4. Power on and Reset control” for detail of “Reset” condition. |
Codice articolo simile - LC78615E |
|
Descrizione simile - LC78615E |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |