Motore di ricerca datesheet componenti elettronici |
|
AD693BQ Scheda tecnica(PDF) 7 Page - Analog Devices |
|
AD693BQ Scheda tecnica(HTML) 7 Page - Analog Devices |
7 / 12 page AD693 REV. A –7– Figure 11. Using an External Pass Transistor to Minimize Self-Heating Errors of adjustment of the output current from nominal. Substitute this value in the appropriate formula below for adjustment at the 4 mA tap. RZ1 = (1.6 V/IA) – 400 Ω and RZ2 = RZ1 × 3.1 V/(15 mV + IA × 3.75 Ω) Use a similar connection with the following resistances for adjustments at the 12 mA tap. RZ1 = (4.8 V/IA) – 400 Ω and RZ2 = RZ1 × 3.1 V/(45 mV + I A × 3.75 Ω) These formulae take into account the ±10% tolerance of tap resistance and insure a minimum adjustment range of IA. For example, choosing IA = 200 µA will give a zero adjustment range of ±1% of the 20 mA full-scale output. At the 4 mA tap the maximum value of: RZ1 = 1.6 V/200 µA – 400 Ω = 7.6 kΩ and RZ2 = 7.6 k Ω × 3.1 V/(15 mV + 200 µA × 3.75 Ω) = 1.49 MΩ Figure 12. Optional 4 mA Zero Adjustment (12 mA Trim Available Also) These can be rounded down to more convenient values of 7.5 k Ω and 1.3 MΩ, which will result in an adjustment range comfortably greater than ±200 µA. ADJUSTING INPUT SPAN Input Span is adjusted by changing the gain of the Signal Amplifier. This amplifier provides a 0-to-60 mV signal to the V/I section to produce the 4-to-20 mA output span (or a 0-to-75 mV signal in the 0-to-20 mA mode). The gain of this amplifier is trimmed to 2.00 so that an input signal ranging from 0-to-30 mV will drive the V/I section to produce 4-to -20 mA. Joining P1 and P2 (Pins 15 and 16) will reduce the Signal Ampli- fier gain to one, thereby requiring a 60 mV signal to drive the V/I to a full 20 mA span. To produce spans less than 30 mV, an external resistor, RS1, can be connected between P1 and 6.2 V. The nominal value is given by: R S1 = 400 Ω 30 mV S −1 where S is the desired span. For example, to change the span to 6 mV a value of: R S1 = 400 Ω 30 mV 6 mV −1 = 100 Ω is required. Since the internal, 800 Ω gain setting resistors exhibit an absolute tolerance of 10%, RS1 should be provided with up to ±10% range of adjustment if the span must be well controlled. For spans between 30 mV and 60 mV a resistor RS2 should be connected between P1 and P2. The nominal value is given by: RS2 = 400 Ω 1− 60 mV S 30 mV S −1 For example, to change the span to 40 mV, a value of: R S2 = 400 Ω 1− 60 mV 40 mV 30 mV 40 mV −1 = 800 Ω is required. Remember that this is a nominal value and may require adjustment up to ±10%. In many applications the span must be adjusted to accommodate individual variations in the sensor as well as the AD693. The span changing resistor should, therefore, include enough adjustment range to handle both the sensor uncertainty and the absolute resistance tolerance of P1 and P2. Note that the temperature coefficient of the internal resistors is nominally –17 ppm/ °C, and that the external resistors should be comparably stable to insure good tempera- ture performance. |
Codice articolo simile - AD693BQ |
|
Descrizione simile - AD693BQ |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |