Motore di ricerca datesheet componenti elettronici |
|
AD7709ARU Scheda tecnica(PDF) 6 Page - Analog Devices |
|
AD7709ARU Scheda tecnica(HTML) 6 Page - Analog Devices |
6 / 32 page REV. A AD7709 –6– TIMING CHARACTERISTICS1, 2 Limit at TMIN, TMAX Parameter (A, B Version) Unit Conditions/Comments t1 30.5176 ms typ Crystal Oscillator Period t2 50 ns min RESET Pulsewidth Read Operation t3 0 ns min RDY to CS Setup Time t4 0 ns min CS Falling Edge to SCLK Active Edge Setup Time3 t5 4 0 ns min SCLK Active Edge to Data Valid Delay 3 60 ns max VDD = 4.75 V to 5.25 V 80 ns max VDD = 2.7 V to 3.6 V t5A 4, 5 0 ns min CS Falling Edge to Data Valid Delay 60 ns max VDD = 4.75 V to 5.25 V 80 ns max VDD = 2.7 V to 3.6 V t6 100 ns min SCLK High Pulsewidth t7 100 ns min SCLK Low Pulsewidth t8 0 ns min CS Rising Edge to SCLK Inactive Edge Hold Time3 t9 6 10 ns min Bus Relinquish Time after SCLK Inactive Edge 3 80 ns max t10 100 ns max SCLK Active Edge to RDY High3, 7 Write Operation t11 0 ns min CS Falling Edge to SCLK Active Edge Setup Time3 t12 30 ns min Data Valid to SCLK Edge Setup Time t13 25 ns min Data Valid to SCLK Edge Hold Time t14 100 ns min SCLK High Pulsewidth t15 100 ns min SCLK Low Pulsewidth t16 0 ns min CS Rising Edge to SCLK Edge Hold Time NOTES 1 Sample tested during initial release to ensure compliance. All input signals are specified with t R = tF = 5 ns (10% to 90% of VDD) and timed from a voltage level of 1.6 V. 2 See Figures 2 and 3. 3 SCLK active edge is falling edge of SCLK. 4 These numbers are measured with the load circuit of Figure 1 and defined as the time required for the output to cross the V OL or VOH limits. 5 This specification comes into play only if CS goes low while SCLK is low. It is required primarily for interfacing to DSP machines. 6 These numbers are derived from the measured time taken by the data output to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapo- lated back to remove effects of charging or discharging the 50 pF capacitor. This means that the times quoted in the Timing Characteristics table are the true bus relinquish times of the part and as such are independent of external bus loading capacitances. 7 RDY returns high after a read of the ADC. The same data can be read again, if required, while RDY is high, although care should be taken that subsequent reads do not occur close to the next output update. (VDD = 2.7 V to 3.6 V or VDD = 4.75 V to 5.25 V; GND = 0 V; XTAL = 32.768 kHz; Input Logic 0 = 0 V, Logic 1 = VDD unless otherwise noted.) |
Codice articolo simile - AD7709ARU |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |