Motore di ricerca datesheet componenti elettronici |
|
TS3300ITQ1633TP Scheda tecnica(PDF) 9 Page - Touchstone Semiconductor Inc |
|
TS3300ITQ1633TP Scheda tecnica(HTML) 9 Page - Touchstone Semiconductor Inc |
9 / 14 page TS3300 TS3300DS r1p0 Page 9 RTFDS PIN FUNCTIONS PIN NAME FUNCTION 1 BIN Boost Input. Bypass this pin with a 22µF ceramic capacitor in close proximity to the TS3300. 2 CCP Charge Pump Capacitor. Place a 3.3nF capacitor between this pin and GND 3 BEN Boost Enable (active low). To enable the TS3300, connect this to GND. To disable the TS3300, set the voltage to greater than VBI – 50mV. 4 BI FB Boost Input Feedback for Anti-Crush Voltage Setting. The BI FB pin voltage is 392mV. To set the anti-crush voltage, refer to the Applications Information section and to Figure 7. 5 FAC Factory use only. Do not connect to GND or VDD. Leave open. 6 SW EN Switch Enable. When SW EN is high and REG EN is low, the internal FET/SWITCH connects the LDO output to the LDO input. The internal FET has an RdsON = 1.2 . Refer to Table 1. 7 REG EN LDO Regulator Enable. When REG EN is high and SW EN is low, the LDO is under normal operation. Refer to Table 1. 8 REG FB LDO Regulator Output Feedback. The REG FB pin voltage is 505mV. REG FB coupled with a voltage divider circuit sets the LDO output voltage. Refer to Figure 3. 9 GND Ground. Connect this pin to the analog ground plane 10 REGOUT LDO Regulator Output Voltage. A minimum output capacitance of 10µF is recommended to be placed from this pin to GND. To set the LDO output voltage, use a voltage divider circuit along with the REG FB pin as shown in Figure 3. 11 REGIN LDO Regulator Input/Boost Output. REGIN should always be connected to the boost regulator output voltage pin BO. BO is always the input to the LDO. Do not apply an external supply voltage to this pin. 12 GND Ground. Connect this pin to the analog ground plane. 13 BO FB Boost Output Feedback. The BO FB pin voltage is 505mV. BO FB coupled with a voltage divider circuit sets the boost regulator output voltage. Refer to Figure 2. 14 BO Boost Regulator Output Voltage. A minimum output capacitance of 10µF is recommended to be placed from this pin to GND. To set the boost regulator output voltage, use a voltage divider circuit along with the BO FB pin. Refer to Figure 2. 15 LSW Coil is a low-ESR, high-saturation current, shielded inductor. A 10µH inductor is recommended for most applications and is to be placed from this pin to the input of the boost regulator BI. Furthermore, there should exist at least an 8% margin between the saturation current of the inductor and the peak inductor current for a given set of operating conditions. 16 GND Ground. Connect this pin to the analog ground plane. EP For best electrical and thermal performance, connect exposed paddle to GND. |
Codice articolo simile - TS3300ITQ1633TP |
|
Descrizione simile - TS3300ITQ1633TP |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |