Motore di ricerca datesheet componenti elettronici |
|
AD1862 Scheda tecnica(PDF) 7 Page - Analog Devices |
|
AD1862 Scheda tecnica(HTML) 7 Page - Analog Devices |
7 / 12 page TOTAL HARMONIC DISTORTION + NOISE The THD figure of an audio DAC represents the amount of un- desirable signal produced during reconstruction and playback of an audio waveform. The THD specification, therefore, provides a direct method to classify and choose an audio DAC for a de- sired level of performance. By combining noise measurement with the THD measurement, a THD+N specification is realized. This specification indicates all of the undesirable signal produced by the DAC, including harmonic products of the test tone as well as noise. Analog Devices tests all AD1862s on the basis of THD+N per- formance. In this test procedure, a digital data stream represent- ing a 0 dB, –20 dB or –60 dB sine wave is sent to the device under test. The frequency of the waveform is 990.5 Hz. Input data is sent to the AD1862 at an 8 × F S rate (352.8 kHz). The AD1862 under test produces an output current which is con- verted to an output voltage by an external amplifier. Figure 10 illustrates the recommended test circuit. Deglitchers and trims are not used during this test procedure. The automatic test equipment digitizes 4096 samples of the output test waveform, incorporating 23 complete cycles of the sine wave. A 4096 point FFT is performed on the test data. V OUT AD1862 TOP VIEW (Not to Scale) 1 2 3 4 5 6 7 89 10 11 12 13 14 15 16 Figure 9. External Amplifier Connections Based upon the harmonics of the fundamental 990.5 Hz test tone, and the noise components in the audio band, the total har- monic distortion + noise of the device is calculated. The AD1862 is available in two performance grades. The AD1862N produces a maximum of 0.0025% THD+N at 0 dB signal lev- els. The higher performance AD1862N-J produces a maximum of 0.0016% THD+N at 0 dB signal levels. SIGNAL-TO-NOISE RATIO The Signal-to-Noise Ratio (SNR) of the AD1862 is tested in the following manner. The amplitude of a 0 dB signal is measured. The device under test is then set to midscale output voltage (0 volts). The amplitude of all noise present to 30 kHz is mea- sured. The SNR is the ratio of these two measurements. The SNR figure for the AD1862 includes the output noise contrib- uted by the NE5534 op amp used in the test fixture but does not include the noise contributed by the low-pass filter used in the test fixture. The AD1862N has a minimum SNR of 110 dB. The higher performance AD1862N-J has a minimum SNR of 113 dB. Testing the AD1862 REV. A –7– AD1862 TOP VIEW (Not to Scale) 1 2 3 4 5 6 7 89 10 11 12 13 14 15 16 0.1 µF 0.1 µF 0.1 µF 0.1 µF 10 µF 1 µF 3-POLE LOW PASS FILTER 12V – 12V 12V – 17MHz 352.8kHz DIGITAL COMMON SE5534A OUTPUT VOLTAGE ANALOG COMMON 12V 360pF + + Figure 10. Recommended Test Circuit |
Codice articolo simile - AD1862 |
|
Descrizione simile - AD1862 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |