Motore di ricerca datesheet componenti elettronici |
|
STD Scheda tecnica(PDF) 2 Page - Texas Instruments |
|
STD Scheda tecnica(HTML) 2 Page - Texas Instruments |
2 / 15 page Introduction www.ti.com 1 Introduction The TPS62160 is a 1-A, synchronous, step-down converter in a 2x2-mm, 8-pin WSON package. Both fixed and adjustable output voltage units are available. The TPS62170 is a 0.5-A, synchronous, step-down converter in a 2x2-mm, 8-pin WSON package. Both fixed and adjustable output voltage units are available. 1.1 Background The TPS62160EVM-627 (HPA627-001) uses the TPS62160 adjustable version and is set to a 3.3-V output. The EVM operates with full-rated performance with an input voltage between 3.7 V and 17 V. The TPS62170EVM-627 (HPA627-002) uses the TPS62170 adjustable version and is set to a 3.3-V output. The EVM operates with full-rated performance with an input voltage between 3.7 V and 17 V. 1.2 Performance Specification Table 1 provides a summary of the TPS621x0EVM-627 performance specifications. All specifications are given for an ambient temperature of 25 °C. Table 1. Performance Specification Summary Specification Test Conditions Min Typ Max Unit Input Voltage 3.7 17 V Output Voltage PWM Mode of Operation 3.227 3.327 3.427 V Output Current TPS62160EVM-627 0 1000 mA TPS62170EVM-627 0 500 mA Peak Efficiency 93.1 % Soft-Start Time 180 µs 1.3 Modifications The printed-circuit board (PCB) for this EVM is designed to accommodate both the fixed and adjustable voltage versions of this integrated circuit (IC). Additional input and output capacitors can also be added. Finally, the loop response of the IC can be measured. 1.3.1 Fixed Output Operation U1 can be replaced with the fixed-voltage version of the IC for evaluation. For fixed-voltage version operation, replace R2 with a 0- Ω resistor and remove R1. 1.3.2 Input and Output Capacitors C4 is provided for an additional input capacitor. This capacitor is not required for proper operation but can be used to reduce the input voltage ripple. C3 is provided for an additional output capacitor. This capacitor is not required for proper operation but can be used to reduce the output voltage ripple and to improve the load transient response. The total output capacitance must remain within the recommended range in the data sheet for proper operation. 1.3.3 Loop Response Measurement The loop response of the TPS621x0EVM-627 can be measured with two simple changes to the circuitry. First, install a 10- Ω resistor across the pads in the middle of the back of the PCB. The pads are spaced to allow installation of 0805- or 0603-sized resistors. Second, cut the short section of trace between the via on the output voltage and the trace that connects to the VOS pin via. These changes are shown in Figure 1. With these changes, an ac signal (10-mV, peak-to-peak amplitude recommended) can be injected into the control loop across the added resistor. 2 TPS62160EVM-627 and TPS62170EVM-627 — Evaluation Modules SLVU483 – October 2011 Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated |
Codice articolo simile - STD |
|
Descrizione simile - STD |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |