Motore di ricerca datesheet componenti elettronici |
|
DAC716P Scheda tecnica(PDF) 8 Page - Texas Instruments |
|
DAC716P Scheda tecnica(HTML) 8 Page - Texas Instruments |
8 / 16 page 8 ® DAC716 DAC716 CALIBRATION VALUES 1 LEAST SIGNIFICANT BIT = 152 µV DIGITAL INPUT CODE ANALOG OUTPUT (V) STRAIGHT BINARY UNIPOLAR 10V RANGE DESCRIPTION FFFFH +9.999695 + Full Scale –1LSB | 8000 H +5.000000 Half Scale 0000H 0.000000 Unipolar Zero TABLE I. Digital Input and Analog Output Voltage Calibra- tion Values. INSTALLATION GENERAL CONSIDERATIONS Due to the high precision of these D/A converters, system design problems such as grounding and contact resistance become very important. A 16-bit converter with a 10V full- scale range has a 1LSB value of 152 µV. With a load current of 5mA, series wiring and connector resistance of only 60m Ω will cause a voltage drop of 300µV. To understand what this means in terms of a system layout, the resistivity of a typical 1 ounce copper-clad printed circuit board is 1/2 m Ω per square. For a 5mA load, a 0.1 inch wide printed circuit conductor 0.6 inches long will result in a voltage drop of 150 µV. The analog output of DAC716 has an LSB size of 152 µV (–96dB). The rms noise floor of the D/A should remain below this level in the frequency range of interest. The DAC716’s output noise spectral density (which includes the noise contrib- uted by the internal reference) is shown in the Typical Perfor- mance Curves section. Wiring to high-resolution D/A converters should be routed to provide optimum isolation from sources of RFI and EMI. The key to elimination of RF radiation or pickup is small loop area. Signal leads and their return conductors should be kept close together such that they present a small capture cross-section for any external field. Wire-wrap construction is not recommended. POWER SUPPLY AND REFERENCE CONNECTIONS Power supply decoupling capacitors should be added as shown in Figure 4. Best performance occurs using a 1 to 10 µF tantalum capacitor at –V CC. Applications with less critical settling time may be able to use 0.01 µF at –V CC as well as at +VCC. The capacitors should be located close to the package. The DAC716 has separate ANALOG COMMON and DIGI- TAL COMMON pins. The current through DCOM is mostly switching transients and are up to 1mA peak in amplitude. The current through ACOM is typically 5 µA for all codes. Use separate analog and digital ground planes with a single interconnection point to minimize ground loops. The analog FIGURE 4. Power Supply Connections. 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 1µF 1µF DAC716 DCOM +V CC ACOM –V CC +12V to +15V –12V to –15V + + pins are located adjacent to each other to help isolate analog from digital signals. Analog signals should be routed as far as possible from digital signals and should cross them at right angles. A solid analog ground plane around the D/A package, as well as under it in the vicinity of the analog and power supply pins, will isolate the D/A from switching currents. It is recommended that DCOM and ACOM be connected directly to the ground planes under the package. If several DAC716s are used or if the DAC716 shares supplies with other components, connecting the ACOM and DCOM lines together at the power supplies only rather than at each chip, may give better results. LOAD CONNECTIONS Since the reference point for VOUT and VREF OUT is the ACOM pin, it is important to connect the D/A converter load directly to the ACOM pin. Refer to Figure 5. Lead and contact resistances are represented by R1 through R3. As long as the load resistance RL is constant, R1 simply introduces a gain error and can be removed by gain adjust- ment of the D/A or system-wide gain calibration. R2 is part of RL if the output voltage is sensed at ACOM. In some applications it is impractical to return the load to the ACOM pin of the D/A converter. Sensing the output voltage at the SYSTEM GROUND point is reasonable, because there is no change in DAC716 ACOM current, provided that R3 is a low-resistance ground plane or conductor. In this case you may wish to connect DCOM to SYSTEM GROUND as well. GAIN AND OFFSET ADJUST Connections Using Potentiometers GAIN and OFFSET adjust pins provide for trim using external potentiometers. 15-turn potentiometers provide suf- ficient resolution. Range of adjustment of these trims is at least ±0.3% of Full Scale Range. Refer to Figure 6. |
Codice articolo simile - DAC716P |
|
Descrizione simile - DAC716P |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |