Motore di ricerca datesheet componenti elettronici |
|
2-1195133-5 Scheda tecnica(PDF) 2 Page - PANDUIT CORP. |
|
2-1195133-5 Scheda tecnica(HTML) 2 Page - PANDUIT CORP. |
2 / 2 page SPECIFICATION CONTROL DRAWING DOCUMENT NO.: D-436-88/-90 DCR NUMBER: D060019 REV.: B1 DATE: 16-Apr-11 SHEET: 2 of 2 Print Date: 9-May-11 © 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company. All Rights Reserved. If this document is printed it becomes uncontrolled. Check for the latest revision. MIL Spec equivalent size and wire accomodation: APPLICATION 1. These parts are designed to provide immersion resistant in-line splices of 2 or 3 to 2 or 3 wires falling within the size range listed on sheet 1, having nickel-plated conductors and insulations rated for at least 135C. 2. Parts are available only as an assembly of one of each Item #1 and Item #2. 3. Parts are to be installed per assembly procedure as outlined below. 4. Inside diameter and outside diameter of splice are to be measured in crimp area, 2.54 to 5.08mm [0.100 to 0.200in] from ends of part. Slight burr permitted on parted surfaces. 5. Acceptance sampling shall be in accordance with Paragraph 4.6.1 of SAE AS81824. 6. Packing and packaging shall be in accordance with Section 5, Level C, of SAE AS81824. 7. This document takes precedence over documents referenced herein. ASSEMBLY PROCEDURE 1.0 SCOPE This document outlines the procedure to be followed to obtain immersion resistant multiple wire butt splices using Multi-Wire In-Line Splice Sealing system D-436-88/-90. 2.0 PROCEDURE a) Pass the wires to be attached to one barrel through the separate multi-wire seal (3). Pass the wires to be attached to the other barrel through the sealing sleeve from the three hole insert end. b) Strip wires 5/16” to 11/32” and crimp into splice using a Raychem AD-1377 crimp tool. Care must be taken so that the wires remain untwisted between the splice and the separate multi-wire seal (3) or the sealing sleeve cannot be positioned properly. c) Position the separate multi-wire seal (3) as close as possible to the splice. Hold this piece in position by squeezing the wires directly behind it, and slide the sealing sleeve over the assembly so that the separate multi-wire seal (3) is as far inside the sleeve as possible. d) Apply heat, using the recommended heat source, first to the separate multi-wire seal end, and then to the other. Heat should be applied until insert melts and flows axially along the wire. 3.0 RECOMMENDED RAYCHEM HEATING TOOLS Heater Reflector Recommended setting Heat Gun CV-1981 PR52D 7.5 - 8 Steinel HL-1802E PR52D 8 - 9 Unless otherwise specified, dimensions are in millimeters. [Inches dimensions are shown in rackets] Part Name MIL Spec Equivalent Size Wire Size Range (AWG) Wgt. Lbs/Mpc max D-436-88 M81824/1-1 26 - 20 1.02 D-436-89 M81824/1-2 20 - 16 1.61 D-436-90 M81824/1-3 16 - 12 2.72 |
Codice articolo simile - 2-1195133-5 |
|
Descrizione simile - 2-1195133-5 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |