Motore di ricerca datesheet componenti elettronici |
|
LC72707E Scheda tecnica(PDF) 6 Page - Sanyo Semicon Device |
|
LC72707E Scheda tecnica(HTML) 6 Page - Sanyo Semicon Device |
6 / 15 page No. 5970-6/15 LC72707E Layer 4 CRC Data Input Timing Serial Control Data Input Settings The input data consists of 16 bits (DI0 to DI15). The upper 8 bits (DI8 to DI15) are the control address and the lower 8 bits (DI0 to DI7) are the input data. Bits DI12 to DI15 are ignored. • Number of Allowed BIC Errors This IC’s synchronization circuit operates by recognizing a 16-bit BIC code. The number of allowed errors is the number of allowed error bits in the 16 bits used for BIC recognition. This data item allows the forward protection mode (used when synchronized) and the backward protection mode (used when not synchronized) values to be set independently. The default value is to allow up to 2 error bits in both the forward and backward directions. We recommend setting the backward protection mode number of allowable BIC errors to 1 or 0 if the block synchronization recognition output (the BLOCK pin, pin 23) is used to recognize the presence or absence of FM multiplex data. • Block Synchronization Error Protection Count The synchronization protection count can be set independently in the forward and backward directions. The protection count conditions are as follows. — Backward protection (unsynchronized, BLOCK = low) When the timing of the IC’s internal synchronization free-running counter matches that of the received BIC, the protection count is incremented by 1. Similarly, if the IC internal counter and the received BIC do not match, the counter is cleared to 0. The count timing is the timing of the IC internal counter. — Forward protection (synchronized, BLOCK = high) Operation is the opposite of the backward case, namely, the protection count is incremented when the timing of the IC’s internal synchronization free-running counter does not match that of the received BIC, and the protection count is cleared to zero when the timing matches. Figure 1 shows the protection counter when both the forward and backward protection counts are set to 3. This IC defines the protection counter value to be 1 at the point where a match or a mismatch occurs between the IC internal timing and the received BIC timing. For example, a backward protection count of 2 corresponds to the case where the IC internal timing and the received BIC timing match two times consecutively. To set the protection data to new values, applications must send data in which 1 has been subtracted from the desired values, e.g. to set up protection counts of 3 as shown in figure 1, applications must send the value 22H. Similarly, if the value set is 00, due to the definition, the protection counts for both the forward and backward directions will be set to 1. However, from an operation standpoint, this corresponds to operation equivalent to there being no protection circuit. The default values are a forward protection count of 8 and a backward protection count of 2. We recommend resetting the block synchronization backward protection count to a value more strict than the default, CRC4 pin output Note: The N items are 8-bit units. CRC4 output after N items transferred Register Address Data Default DI11 DI10 DI9 DI8 setting Number of allowable BIC errors 0 0 0 0 Upper 4 bits Allowed error bits backward 2 Lower 4 bits Allowed error bits forward 2 Number of block error protection states 0 0 0 1 Upper 4 bits Block backward protection 1 Lower 4 bits Block forward protection 7 Number of frame error protection states 0 0 1 0 Upper 4 bits Frame backward protection 1 Lower 4 bits Frame forward protection 7 Control register 0 0 1 1 See the control register description on page 8. |
Codice articolo simile - LC72707E |
|
Descrizione simile - LC72707E |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |