Motore di ricerca datesheet componenti elettronici
  Italian  ▼
ALLDATASHEETIT.COM

X  

LB1976 Scheda tecnica(PDF) 10 Page - Sanyo Semicon Device

Il numero della parte LB1976
Spiegazioni elettronici  DC Fan Motor Driver
Download  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Produttore elettronici  SANYO [Sanyo Semicon Device]
Homepage  https://www.sanyo-av.com/us/
Logo SANYO - Sanyo Semicon Device

LB1976 Scheda tecnica(HTML) 10 Page - Sanyo Semicon Device

Back Button LB1976 Datasheet HTML 4Page - Sanyo Semicon Device LB1976 Datasheet HTML 5Page - Sanyo Semicon Device LB1976 Datasheet HTML 6Page - Sanyo Semicon Device LB1976 Datasheet HTML 7Page - Sanyo Semicon Device LB1976 Datasheet HTML 8Page - Sanyo Semicon Device LB1976 Datasheet HTML 9Page - Sanyo Semicon Device LB1976 Datasheet HTML 10Page - Sanyo Semicon Device LB1976 Datasheet HTML 11Page - Sanyo Semicon Device LB1976 Datasheet HTML 12Page - Sanyo Semicon Device  
Zoom Inzoom in Zoom Outzoom out
 10 / 12 page
background image
Hall Input Circuit
The Hall input circuit is a differential amplifier with a hysteresis of 32 mV (typ.). The operation DC level must be within
the common-mode input voltage range (1.5 V to VCC – 1.5 V). To prevent noise and other adverse influences, the input
level should be at least 3 times the hysteresis (120 to 160 mVp-p). If noise at the Hall input is a problem, a noise-
canceling capacitor (about 0.01 µF) should be connected across the Hall input IN+ and INpins.
FG Output Circuit
The Hall input signal at IN1, IN2, and IN3 is combined and subject to waveform shaping before being output. The signal
at FG1 has the same frequency as the FG1 Hall input, and the signal at FG2 has a frequency that is three times higher.
Start/Stop Control Circuit
The start/stop control circuit turns the source-side output transistors OFF (motor stop) when a High signal is input at the
S/S pin or when the pin is Open. When a Low signal is input at the S/S pin, the source-side output transistors are turned
ON, and the normal operation state is established (motor start).
Forward/Reverse Switching
This IC is designed under the assumption that forward/reverse switching is not carried out while the motor is running. If
switching is carried out while the motor is running, reverse torque braking occurs, leading to a high current flow. If the
current limiter is triggered, the source-side output transistors are switched off, and the sink-side output transistors go into
the short brake condition. However, because the current limiter of this IC cannot control the current flowing in the sink-
side output transistors, these may be destroyed by the short brake current. Therefore F/R switching while the motor is
running is permissible only if the output current (IO) is limited to a maximum of 2.5 A using the motor coil resistance or
other suitable means.
F/R switching should be carried out only while a High signal is input to the S/S pin or the pin is Open (stop condition), or
while the VCTL pin conforms to the following condition: VCTL ≤ VCTL1 (duty cycle 0%). In any other condition, F/R
switching will result in feedthrough current. The F/R pin should therefore be fixed to Low (forward) or High or Open
(reverse) during use.
VCC, VM Power Supplies
When the power supply voltage (VCC, VM) rises very quickly when a power is first applied, a feedthrough current may
occur at the output. If the current remains below about 0.2 A to 0.3 A, it does not pose a problem, but such a possibility
should still be prevented by slowing down the voltage rise at power-on. Especially if the F/R pin is set to High or Open
(reverse), a quick rise in VCC is likely to cause feedthrough current. This should be prevented by ensuring that ∆VCC / ∆t
= 0.2 V/µs or less. Feedthrough current can also be prevented by first switching on VCC and then VM during power-on.
The sequence at power-down should be as follows. Provide a stop input to the S/S pin or a duty ratio 0% input to the
VCTL pin. When the motor has come to a full stop, switch off VM and then VCC. If power is switched off while the
motor is still rotating or a current is flowing in the motor coil (including motor restraint or inertia rotation), a
counterelectromotive current or kickback current may flow on the VM side, depending on the motor type and power-off
procedure. If this current cannot be absorbed by the VM power supply or a capacitor, VM voltage may rise and exceed
the absolute maximum VM rating for the IC. Ensure that this does not happen through proper design of the VM power
supply or through use of a capacitor.
Because the IC (LB1976) incorporates a shunt regulator, it can be used on a single power supply. In this case, supply
VCC (6.3 typ.) to the VREG pin via an external NPN transistor and resistor. When not using the regulator, leave the VREG
pin open.
No. 6088-10/12
LB1976


Codice articolo simile - LB1976

Produttore elettroniciIl numero della parteScheda tecnicaSpiegazioni elettronici
logo
Sanyo Semicon Device
LB1976 SANYO-LB1976 Datasheet
141Kb / 10P
   For Fan Motor 3-phase Brushless Motor Driver
logo
ON Semiconductor
LB1976 ONSEMI-LB1976 Datasheet
135Kb / 10P
   3-phase Brushless Motor Driver
May, 2013
logo
Sanyo Semicon Device
LB1976 SANYO-LB1976_08 Datasheet
141Kb / 10P
   For Fan Motor 3-phase Brushless Motor Driver
More results

Descrizione simile - LB1976

Produttore elettroniciIl numero della parteScheda tecnicaSpiegazioni elettronici
logo
Sanyo Semicon Device
LB1975 SANYO-LB1975 Datasheet
91Kb / 12P
   DC Fan Motor Driver
LB1695M SANYO-LB1695M Datasheet
89Kb / 7P
   DC Fan Motor Driver
logo
Hitachi Semiconductor
HA13460FP HITACHI-HA13460FP Datasheet
76Kb / 4P
   BRUCHLESS DC FAN MOTOR DRIVER
logo
Unisonic Technologies
SK1288 UTC-SK1288_15 Datasheet
78Kb / 8P
   2-PHASE DC-FAN MOTOR DRIVER
SK6908 UTC-SK6908_15 Datasheet
137Kb / 6P
   SINGLE-PHASE DC-FAN MOTOR DRIVER
SK6908 UTC-SK6908 Datasheet
255Kb / 6P
   SINGLE-PHASE DC-FAN MOTOR DRIVER
SK1288 UTC-SK1288 Datasheet
73Kb / 8P
   2-PHASE DC-FAN MOTOR DRIVER
logo
Toshiba Semiconductor
TA8420AF TOSHIBA-TA8420AF Datasheet
442Kb / 11P
   1 CHIP DC FAN MOTOR DRIVER
logo
Unisonic Technologies
SK6908 UTC-SK6908_07 Datasheet
137Kb / 6P
   SINGLE-PHASE DC-FAN MOTOR DRIVER
F6406 UTC-F6406_15 Datasheet
202Kb / 5P
   2-PHASE DC-FAN MOTOR DRIVER
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


Scheda tecnica Scarica

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEETIT.COM
Lei ha avuto il aiuto da alldatasheet?  [ DONATE ] 

Di alldatasheet   |   Richest di pubblicita   |   contatti   |   Privacy Policy   |   scambio Link   |   Ricerca produttore
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com