 |
Motore di ricerca datesheet componenti elettronici |
|
|
Motore di ricerca datesheet componenti elettronici |
|
0-273-141-043 Scheda tecnica(PDF) 5 Page - List of Unclassifed Manufacturers |
|
||||||||||||||||||||||||||||||
0-273-141-043 Scheda tecnica(HTML) 5 Page - List of Unclassifed Manufacturers |
|
|
5 / 55 page  Data sheet BMA150 Triaxial, digital acceleration sensor Bosch Sensortec Rev. 1.5 Page 5 30 May 2008 © Bosch Sensortec GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. BOSCH and the symbol are registered trademarks of Robert Bosch GmbH, Germany. Note: Specifications within this document are subject to change without notice. 1. Specification If not stated otherwise, the given values are maximum values over lifetime and full performance temperature/voltage range in the normal operation mode. Table 1: Operating range, output signal and mechanical specifications of BMA150 Parameter Symbol Condition Min Typ Max Units OPERATING RANGE gFS2g -2 2 g gFS4g -4 4 g Acceleration range gFS8g Switchable via serial digital interface -8 8 g Supply voltage analogue VDD 2.4 3.6 V Supply voltage for digital I/O VDDIO VDDIO ≤ VDD 1.62 3.6 V Supply current in normal mode IDD Digital and analog 200 290 µA Supply current in stand-by mode * IDDsbm Digital and analog 1 2 µA Operating temperature TA -40 +85 °C ACCELERATION OUTPUT SIGNAL Acceleration output resolution Format: 2’s complement 10 Bit S2g g-range ±2g 246 256 266 LSB/g S4g g-range ±4g 122 ** 128 134 ** LSB/g Sensitivity S8g g-range ±8g 61 ** 64 67 ** LSB/g Zero-g offset Off TA=25°C, calibrated -60 60 mg Zero-g offset Off TA=25°C , over lifetime *** -150 150 mg Zero-g offset temperature drift Over TA 1 mg/K Power supply rejection ratio PSRR Over VDD 0.2 LSB/V * For more details on the BMA150’s current consumption during wake-up mode, please refer to chapter 7.2 & 7.3 ** Values here are given as indications for reference only *** The offset can deviate from the original calibration mainly due to stress effects during soldering depending on the soldering process. For many applications it is beneficial to re-calibrate the offset after PCB assembly (see application note ANA016 “In-line offset re-calibration”). |
Codice articolo simile - 0-273-141-043 |
|
Descrizione simile - 0-273-141-043 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEETIT.COM |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Italian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
