Motore di ricerca datesheet componenti elettronici |
|
BD3823FV Scheda tecnica(PDF) 7 Page - Rohm |
|
BD3823FV Scheda tecnica(HTML) 7 Page - Rohm |
7 / 9 page 7/8 How to select application parts Initial condition when power supply (17 pin) is turned ON A circuit that carries out initialization in IC, when power supply (17 pin) is turned ON is incorporated. Settings are as shown in the following table. However, it is recommended to transmit the data to all the addresses as initial data when power is turned ON, and to apply mute while the initial data is input Limits Parameter Symbol Min. Typ. Max. Unit Conditions VCC rise time Trise 20 - - S VCC rise time from 0V to 3V VCC voltage when power on reset is released. Vpor - 2.6 - V Function Initial Condition Input Selector Input MUTE Volume - dB Gain SERECTOR 0dB Signal input section 1) Setting for input coupling capacitor In the signal input terminal, set the constant for the input coupling capacitor C(F), taking the input impedance RIN ( ) inside into account. This makes up the primary HPF characteristics of the RC. 2) SHORT mode of input SHORT mode is a command to reduce resistance by setting impedance RIN to switch SSH ON. When SHORT command is not chosen, switch SSH is turned OFF. By using this command, it is possible to stop charging externally mounted coupling capacitor C. Use SHORT mode when there is no signal since the SHORT mode turns ON the SSH switch in order to achieve low impedance. Operation Notes 1. Numbers and data in entries are representative design values and are not guaranteed values of the items. 2. Although ROHM is confident that the example application circuit reflects the best possible recommendations, be sure to verify circuit characteristics for your particular application. Modification of constants for other externally connected circuits may cause variations in both static and transient characteristics for external components as well as this Rohm IC. Allow for sufficient margins when determining circuit constants. 3. Absolute maximum ratings Use of the IC in excess of absolute maximum ratings, such as the applied voltage or operating temperature range (Topr), may result in IC damage. Assumptions should not be made regarding the state of the IC (short mode or open mode) when such damage is suffered. A physical safety measure, such as a fuse, should be implemented when using the IC at times where the absolute maximum ratings may be exceeded. 4. GND potential Ensure a minimum GND pin potential in all operating conditions. Make sure that no pins are at a voltage below the GND at any time, regardless of whether it is a transient signal or not. 5. Thermal design Perform thermal design, in which there are adequate margins, by taking into account the permissible dissipation (Pd) in actual states of use. 6. Short circuit between terminals and erroneous mounting Pay attention to the assembly direction of the ICs. Wrong mounting direction or shorts between terminals, GND, or other components on the circuits, can damage the IC. 7. Operation in strong electromagnetic field Using the ICs in a strong electromagnetic field can cause operation malfunction. A(f) GAIN[dB F Hz 0 Fig.15 Sigal input section C F RIN Input terminal SSH |
Codice articolo simile - BD3823FV_05 |
|
Descrizione simile - BD3823FV_05 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |