Motore di ricerca datesheet componenti elettronici |
|
TS34118 Scheda tecnica(PDF) 10 Page - Taiwan Semiconductor Company, Ltd |
|
TS34118 Scheda tecnica(HTML) 10 Page - Taiwan Semiconductor Company, Ltd |
10 / 23 page TS34118 Voice Switched Speakerphone Circuit 10/23 Version: A08 Attenuator Control Block The Attenuator Control Block has the seven inputs described above: -The output of the comparator operated by RLO2 and TLO2 (microphone/speaker side) - designated C1. -The output of the comparator operated by RLO1 and TLO1 (TIP/Ring side) – designated C2. -The output of the transmit background noise monitor – designated C3. -The output of the receive background noise monitor -designated C4. -The volume control. -The dial tone detector. -The AGC circuit. The single output of the Control Block controls the two attenuators. The effect of C1-C4 is as follows: Input Output C1 C2 C3 C4 Mode Tx Tx 1 X Transmit Tx Rx Y Y Fast Idle Rx Tx Y y Fast Idle Rx Rx X 1 Receive Tx Tx 0 X Slow Idle Tx Rx 0 0 Slow Idle Rx Tx 0 0 Slow Idle Rx Rx X 0 Slow Idle X=Don’t Care; y=C3 and C4 are not both 0. A definition of the above terms: 1) ”Transmit” means the transmit attenuator is fully on (+6.0dB), and the receive attenuator is at max. attenuation (- 46dB). 2) ”Receive” means both attenuators are controlled by the volume control. At max. Volume, the receive attenuator is fully on (+6.0dB), and the transmit attenuator is at max. attenuation (-46dB). 3) ”Fast Idle” means both transmit and receive speech is present in approximately equal levels. The attenuators are quickly switched (30ms) to idle until one speech level dominates the other. 4) ”Slow Idle” means speech has ceased in both transmit and receive paths. The attenuators are then slowly switched (1 second) to the idle mode. 5) Switch to the full transmit or receive modes from any other mode is at the fast rate (≈30ms). A summary of the truth table is as follows: 1) The circuit will switch to transmit if: a) both transmit level detectors sense higher signal levels relative to the respective receive level detectors (TLI1 versus RLI1, TLI2 versus RLI2), and b) the transmit background noise monitor indicates the presence of speech. 2) The circuit will switch to receive if: a) both receive level detectors sense higher signal levels relative to the respective transmit level detectors, and b) the receive background noise monitor indicates the presence of speech. 3) The circuit will switch to the fast idle mode if the level detectors disagree on the relative strengths of the signal levels, and at least one of the background noise monitors indicates speech. For example, referring to the Block Diagram (Figure 2), if there is sufficient signal at the microphone amp output (TLI2) to override the speaker signal (RLI2), and there is sufficient signal at the receive input (RLI1) to override the signal at the hybrid output (TLI1), and either or both background monitors indicate speech, then the circuit will be in the fast idle mode. Two conditions which can cause the fast idle mode to occur are a) when both talkers are attempting to gain control of the system by talking at the same time, and b)when one talker is in a very noisy environment, forcing the other talker to continually override that noise level. In general, the fast idle mode will occur infrequently. |
Codice articolo simile - TS34118 |
|
Descrizione simile - TS34118 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |