Motore di ricerca datesheet componenti elettronici
  Italian  ▼
ALLDATASHEETIT.COM

X  

ISL54222AIUZ Scheda tecnica(PDF) 9 Page - Intersil Corporation

Il numero della parte ISL54222AIUZ
Spiegazioni elettronici  High-Speed USB 2.0 (480Mbps) Multiplexer
Download  17 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Produttore elettronici  INTERSIL [Intersil Corporation]
Homepage  http://www.intersil.com/cda/home
Logo INTERSIL - Intersil Corporation

ISL54222AIUZ Scheda tecnica(HTML) 9 Page - Intersil Corporation

Back Button ISL54222AIUZ Datasheet HTML 5Page - Intersil Corporation ISL54222AIUZ Datasheet HTML 6Page - Intersil Corporation ISL54222AIUZ Datasheet HTML 7Page - Intersil Corporation ISL54222AIUZ Datasheet HTML 8Page - Intersil Corporation ISL54222AIUZ Datasheet HTML 9Page - Intersil Corporation ISL54222AIUZ Datasheet HTML 10Page - Intersil Corporation ISL54222AIUZ Datasheet HTML 11Page - Intersil Corporation ISL54222AIUZ Datasheet HTML 12Page - Intersil Corporation ISL54222AIUZ Datasheet HTML 13Page - Intersil Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 17 page
background image
9
FN6902.0
May 13, 2009
1.8V to 3.3V, the fault voltage will pass through to the output of
an active switch channel. During the fault condition normal
operation is not guaranteed until the fault is removed. See the
following “USB 2.0 VBUS Short Requirements” section.
The HS1 channel switches are active (turned ON) whenever
the SEL voltage is logic”0”(Low) and the OE voltage is
logic”0”(Low).
The HS2 channel switches are active (turned ON) whenever
the SEL voltage is logic “1” (High) and the OE voltage is
logic “0” (Low).
ISL54222A Operation
The following will discuss using the ISL54222A shown in the
“Application Block Diagram” on page 8.
POWER
The power supply connected at the VDD pin provides the DC
bias voltage required by the ISL54222A part for proper
operation. The ISL54222A can be operated with a VDD
voltage in the range of 1.8V to 3.3V.
A 0.01µF or 0.1µF decoupling capacitor should be
connected from the VDD pin to ground to filter out any power
supply noise from entering the part. The capacitor should be
located as close to the VDD pin as possible.
LOGIC CONTROL
The state of the ISL54222A device is determined by the
voltage at the SEL pin and the OE pin. SEL is only active
when the OE pin is logic “0” (Low). Refer to “Truth Table” on
page 2.
The ISL54222A logic pins are designed to minimize current
consumption when the logic control voltage is lower than the
VDD supply voltage. With VDD = 3.3V and logic pins at 1.4V,
the part typically draws only 6.6µA. With VDD = 1.8V and
logic pins at 1.4V, the part typically draws only 0.2µA. Driving
the logic pins to the VDD supply rail minimizes power
consumption. The logic pins must be driven High or Low and
must not float.
LOGIC CONTROL VOLTAGE LEVELS
With VDD supply voltage in the range of 1.8V to 3.3V the
logic levels are:
OE = Logic “0” (Low) when VOE 0.5V
OE = Logic “1” (High) when VOE 1.4V
SEL = Logic “0” (Low) when VSEL 0.5V
SEL = Logic “1” (High) when VSEL 1.4V
HSD1 USB CHANNEL
If the SEL pin = Logic “0” and the OE pin = Logic “0”,
high-speed Channel 1 will be ON. The HSD1- and HSD1+
switches are ON and the HSD2- and HSD2+ switches are
OFF (high impedance).
When a computer or USB hub is plugged into the common
USB connector and Channel 1 is active, a link will be
established between the USB 1 transceiver section of the
media player and the computer. The device transceiver 1 will
be able to transmit and receive data from the computer.
HSD2 USB Channel
If the SEL pin = Logic “1” and the OE pin = Logic “0”,
high-speed Channel 2 will be ON. The HSD2- and HSD2+
switches are ON and the HSD1- and HSD1+ switches are
OFF (high impedance).
When a USB cable from a computer or USB hub is
connected at the common USB connector and the part has
Channel 2 active, a link will be established between the USB
2 transceiver section of the media player and the computer.
The device transceiver 2 will be able to transmit and receive
data from the computer.
ALL SWITCHES OFF / LOW POWER MODE
If the SEL pin = Logic “0” or Logic “1” and the OE
pin = Logic “1”, all of the switches will turn OFF (high
impedance) and the part will be put in a low power mode. In
this mode the part draws only 1.5µA (max) of current across
the operating temperature range.
The all OFF state can be used to switch between the two
USB sections of the media player. When disconnecting from
one USB device to the other USB device, you can
momentarily put the ISL54222A switch in the “all off” state in
order to get the computer to disconnect from the one device
so it can properly connect to the other USB device when that
channel is turned ON.
USB 2.0 VBUS Short Requirements
The USB 2.0 specification in chapter 7, section 7.1.1 states
a USB device must be able to withstand a VBUS short to the
D+ or D- signal lines when the device is either powered off or
powered on for at least 24 hours. The ISL54222A part has
special fault protection circuitry to meet these short circuit
requirements.
The fault protection circuitry allows the signal pins (D-, D+,
HSD1-, HSD1+, HSD2-, HSD2+) to be driven up to 5.5V
while the VDD supply voltage is in the range of 0V to 3.3V. In
this overvoltage condition, the part draws < 300µA of IDD
current and causes no stress or damage to the IC.
In addition, when VDD is at 0V (ground), all switches are
OFF and the shorted VBUS voltage is isolated from the other
side of the switch.
When VDD is in the range of 1.8V to 3.3V, the shorted VBUS
voltage will pass through to the output of an active (turned
ON) switch channel but not through a turned OFF channel.
Any components connected on the active channel must be
able to withstand the overvoltage condition.
Note: During the fault condition, normal operation of the USB
channel is not guaranteed until the fault condition is
removed.
ISL54222A


Codice articolo simile - ISL54222AIUZ

Produttore elettroniciIl numero della parteScheda tecnicaSpiegazioni elettronici
logo
Intersil Corporation
ISL54222AIUZ INTERSIL-ISL54222AIUZ Datasheet
908Kb / 19P
   High-Speed USB 2.0 (480Mbps) Multiplexer
logo
Renesas Technology Corp
ISL54222AIUZ RENESAS-ISL54222AIUZ Datasheet
1Mb / 19P
   High-Speed USB 2.0 (480Mbps) Multiplexer
logo
Intersil Corporation
ISL54222AIUZ-T INTERSIL-ISL54222AIUZ-T Datasheet
908Kb / 19P
   High-Speed USB 2.0 (480Mbps) Multiplexer
logo
Renesas Technology Corp
ISL54222AIUZ-T RENESAS-ISL54222AIUZ-T Datasheet
1Mb / 19P
   High-Speed USB 2.0 (480Mbps) Multiplexer
More results

Descrizione simile - ISL54222AIUZ

Produttore elettroniciIl numero della parteScheda tecnicaSpiegazioni elettronici
logo
Renesas Technology Corp
ISL54220 RENESAS-ISL54220 Datasheet
1Mb / 18P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54223 RENESAS-ISL54223 Datasheet
1Mb / 13P
   High-Speed USB 2.0 (480Mbps) Multiplexer
May 27, 2009
logo
Intersil Corporation
ISL54222 INTERSIL-ISL54222 Datasheet
850Kb / 15P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54223 INTERSIL-ISL54223 Datasheet
780Kb / 13P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54220 INTERSIL-ISL54220 Datasheet
808Kb / 15P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54221 INTERSIL-ISL54221 Datasheet
741Kb / 13P
   High-Speed USB 2.0 (480Mbps) Multiplexer
logo
Renesas Technology Corp
ISL54221 RENESAS-ISL54221 Datasheet
1Mb / 13P
   High-Speed USB 2.0 (480Mbps) Multiplexer
logo
Intersil Corporation
ISL54222A INTERSIL-ISL54222A_10 Datasheet
908Kb / 19P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54220 INTERSIL-ISL54220 Datasheet
841Kb / 18P
   High-Speed USB 2.0 480Mbps Multiplexer
ISL54222 INTERSIL-ISL54222_09 Datasheet
856Kb / 15P
   High-Speed USB 2.0 (480Mbps) Multiplexer
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


Scheda tecnica Scarica

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEETIT.COM
Lei ha avuto il aiuto da alldatasheet?  [ DONATE ] 

Di alldatasheet   |   Richest di pubblicita   |   contatti   |   Privacy Policy   |   scambio Link   |   Ricerca produttore
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com