SN54LVTH16240, SN74LVTH16240

3.3-V ABT 16-BIT BUFFERS/DRIVERS

WITH 3-STATE OUTPUTS

SCBS684C – MARCH 1997 – REVISED APRIL 1999

5

POST OFFICE BOX 655303

electrical characteristics over recommended operating free-air temperature range (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

SN54LVTH16240

SN74LVTH16240

UNIT

PARAMETER

TEST CONDITIONS

MIN

TYP†

MAX

MIN

TYP†

MAX

UNIT

VIK

VCC = 2.7 V,

II = –18 mA

–1.2

–1.2

V

VCC = 2.7 V to 3.6 V,

IOH = –100 µA

VCC–0.2

VCC–0.2

VOH

VCC = 2.7 V,

IOH = –8 mA

2.4

2.4

V

VOH

VCC =3V

IOH = –24 mA

2

V

VCC = 3 V

IOH = –32 mA

2

VCC =2 7V

IOL = 100 µA

0.2

0.2

VCC = 2.7 V

IOL = 24 mA

0.5

0.5

VOL

IOL = 16 mA

0.4

0.4

V

VOL

VCC =3V

IOL = 32 mA

0.5

0.5

V

VCC = 3 V

IOL = 48 mA

0.55

IOL = 64 mA

0.55

VCC = 0 or 3.6 V,

VI = 5.5 V

10

10

II

Control inputs

VCC = 3.6 V,

VI = VCC or GND

±1

±1

µA

II

Data inp ts

VCC =3 6V

VI = VCC

1

1

µA

Data inputs

VCC = 3.6 V

VI = 0

–5

–5

Ioff

VCC = 0,

VI or VO = 0 to 4.5 V

±100

µA

VCC =3V

VI = 0.8 V

75

75

II(hold)

Data inputs

VCC = 3 V

VI = 2 V

–75

–75

µA

II(hold)

Data in uts

VCC = 3.6 V‡,

VI = 0 to 3.6 V

500

–750

µA

IOZH

VCC = 3.6 V,

VO = 3 V

5

5

µA

IOZL

VCC = 3.6 V,

VO = 0.5 V

–5

–5

µA

IOZPU

VCC = 0 to 1.5 V, VO = 0.5 V to 3 V,

OE = don’t care

±100*

±100

µA

IOZPD

VCC = 1.5 V to 0, VO = 0.5 V to 3 V,

OE = don’t care

±100*

±100

µA

VCC = 3.6 V,

Outputs high

0.19

0.19

ICC

VCC = 3.6 V,

IO = 0,

Outputs low

5

5

mA

VI = VCC or GND

Outputs disabled

0.19

0.19

∆ICC§

VCC = 3 V to 3.6 V, One input at VCC – 0.6 V,

Other inputs at VCC or GND

0.2

0.2

mA

Ci

VI = 3 V or 0

4

4

pF

Co

VO = 3 V or 0

9

9

pF

∗ On products compliant to MIL-PRF-38535, this parameter is not production tested.

† All typical values are at VCC = 3.3 V, TA = 25°C.

‡ This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to another.

§ This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND.

PRODUCT PREVIEW information concerns products in the formative or

design phase of development. Characteristic data and other

specifications are design goals. Texas Instruments reserves the right to

change or discontinue these products without notice.