Motore di ricerca datesheet componenti elettronici |
|
SN74ALVTH16601DGV Scheda tecnica(PDF) 7 Page - Texas Instruments |
|
SN74ALVTH16601DGV Scheda tecnica(HTML) 7 Page - Texas Instruments |
7 / 12 page SN54ALVTH16601, SN74ALVTH16601 2.5-V/3.3-V 18-BIT UNIVERSAL BUS TRANSCEIVER WITH 3-STATE OUTPUTS SCES143A – SEPTEMBER 1998 – REVISED JULY 1999 7 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 electrical characteristics over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V (unless otherwise noted) PARAMETER TEST CONDITIONS SN54ALVTH16601 SN74ALVTH16601 UNIT PARAMETER TEST CONDITIONS MIN TYP† MAX MIN TYP† MAX UNIT VIK VCC = 3 V, II = –18 mA –1.2 –1.2 V VCC = 3 V to 3.6 V, IOH = –100 µA VCC–0.2 VCC–0.2 VOH VCC =3V IOH = –24 mA 2 V VCC = 3 V IOH = –32 mA 2 VCC = 3 V to 3.6 V, IOL = 100 µA 0.2 0.2 IOL = 16 mA 0.4 VOL IOL = 24 mA 0.5 V VOL VCC = 3 V IOL = 32 mA 0.5 V IOL = 48 mA 0.55 IOL = 64 mA 0.55 VRST‡ VCC = 3.6 V IO = 1 mA, VI = VCC or GND 0.55 0.55 V Control inputs VCC = 3.6 V, VI = VCC or GND ±1 ±1 Control inputs VCC = 0 or 3.6 V, VI = 5.5 V 10 10 II VI = 5.5 V 10 10 µA A or B ports VCC = 3.6 V VI = VCC 1 1 VI = 0 –5 –5 Ioff VCC = 0, VI or VO = 0 to 4.5 V ±100 µA IBHL§ VCC = 3 V, VI = 0.8 V 75 75 µA IBHH¶ VCC = 3 V, VI = 2 V –75 –75 µA IBHLO# VCC = 3.6 V, VI = 0 to VCC 500 500 µA IBHHO|| VCC = 3.6 V, VI = 0 to VCC –500 –500 µA IEXk VCC = 3 V, VO = 5.5 V 125 125 µA IOZ(PU/PD)h VCC ≤ 1.2 V, VO = 0.5 V to VCC, VI = GND or VCC, OE = don’t care ±100 ±100 µA VCC = 3.6 V, Outputs high 0.06 0.1 0.06 0.1 ICC VCC = 3.6 V, IO = 0, Outputs low 3.5 5 3.5 5 mA VI = VCC or GND Outputs disabled 0.06 0.1 0.06 0.1 ∆ICC◊ VCC = 3 V to 3.6 V, One input at VCC – 0.6 V, Other inputs at VCC or GND 0.4 0.4 mA Ci VCC = 3.3 V, VI = 3.3 V or 0 3 3 pF Cio VCC = 3.3 V, VO = 3.3 V or 0 7 7 pF † All typical values are at VCC = 3.3 V, TA = 25°C. ‡ Data must not be loaded into the flip-flops/latches after applying power. § The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and then raising it to VIL max. ¶ The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and then lowering it to VIH min. # An external driver must source at least IBHLO to switch this node from low to high. || An external driver must sink at least IBHHO to switch this node from high to low. kCurrent into an output in the high state when VO > VCC hHigh-impedance state during power up or power down ◊ This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. |
Codice articolo simile - SN74ALVTH16601DGV |
|
Descrizione simile - SN74ALVTH16601DGV |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |