Motore di ricerca datesheet componenti elettronici
  Italian  ▼
ALLDATASHEETIT.COM

X  

TC510COG Scheda tecnica(PDF) 8 Page - TelCom Semiconductor, Inc

Il numero della parte TC510COG
Spiegazioni elettronici  PRECISION ANALOG FRONT ENDS
Download  17 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Produttore elettronici  TELCOM [TelCom Semiconductor, Inc]
Homepage  http://www.telcom-semi.com
Logo TELCOM - TelCom Semiconductor, Inc

TC510COG Scheda tecnica(HTML) 8 Page - TelCom Semiconductor, Inc

Back Button TC510COG Datasheet HTML 4Page - TelCom Semiconductor, Inc TC510COG Datasheet HTML 5Page - TelCom Semiconductor, Inc TC510COG Datasheet HTML 6Page - TelCom Semiconductor, Inc TC510COG Datasheet HTML 7Page - TelCom Semiconductor, Inc TC510COG Datasheet HTML 8Page - TelCom Semiconductor, Inc TC510COG Datasheet HTML 9Page - TelCom Semiconductor, Inc TC510COG Datasheet HTML 10Page - TelCom Semiconductor, Inc TC510COG Datasheet HTML 11Page - TelCom Semiconductor, Inc TC510COG Datasheet HTML 12Page - TelCom Semiconductor, Inc Next Button
Zoom Inzoom in Zoom Outzoom out
 8 / 17 page
background image
3-26
TELCOM SEMICONDUCTOR, INC.
Analog Input Signal Integration Phase (INT)
The TC5xx integrates the differential voltage between
the (V+IN) and (V–IN) inputs. The differential voltage must be
within the device's common-mode range VCMR.
The input signal polarity is normally checked via soft-
ware at the end of this phase: CMPTR = 1 for positive
polarity; CMPTR = 0 for negative polarity.
Reference Voltage Deintegration Phase (DINT)
The previously charged reference capacitor is con-
nected with the proper polarity to ramp the integrator output
back to zero. An externally-provided, precision timer is used
to measure the duration of this phase. The resulting time
measurement is proportional to the magnitude of the applied
input voltage.
Integrator Output Zero Phase (IZ)
This phase guarantees the integrator output is at 0V
when the Auto Zero phase is entered and that only system
offset voltages are compensated. This phase is used at the
end of the reference voltage deintegration phase and MUST
be used for ALL TC5xx applications having resolutions of 12
bits or more. If this phase is not used, the value of the Auto-
Zero capacitor (CAZ) must be about 2 to 3 times the value of
the integration capacitor (CINT) to reduce the effects of
charge-sharing. The Integrator Output Zero phase should
be programmed to operate until the Output of the Compara-
tor returns "HIGH". The overall Timing System is shown in
Figure 8.
ANALOG SECTION
Differential Inputs (V
+
IN, V
IN)
The TC5xx operates with differential voltages within the
input amplifier common-mode range. The amplifier com-
mon-mode range extends from 1.5V below positive supply
to 1.5V above negative supply. Within this common-mode
voltage range, common-mode rejection is typically 80dB.
Full accuracy is maintained, however, when the inputs are
no less than 1.5V from either supply.
The integrator output also follows the common-mode
voltage. The integrator output must not be allowed to satu-
rate. A worst-case condition exists, for example, when a
large, positive common-mode voltage with a near full-scale
negative differential input voltage is applied. The negative
input signal drives the integrator positive when most of its
swing has been used up by the positive common-mode
voltage. For these critical applications, the integrator swing
can be reduced. The integrator output can swing within 0.9V
of either supply without loss of linearity.
Analog Common
Analog common is used as VIN return during system-
zero and reference deintegrate. If V
IN is different from analog
common, a common-mode voltage exists in the system.
This signal is rejected by the excellent CMR of the converter.
In most applications, V
IN will be set at a fixed known voltage
(i.e., power supply common). A common-mode voltage will
exist when V
IN is not connected to analog common.
Differential Reference (V
+
REF, V
REF)
The reference voltage can be anywhere within 1V of the
power supply voltage of the converter. Roll-over error is
caused by the reference capacitor losing or gaining charge
due to stray capacitance on its nodes. The difference in
reference for (+) or (–) input voltages will cause a roll-over
error. This error can be minimized by using a large reference
capacitor in comparison to the stray capacitance.
Phase Control Inputs (A, B)
The A, B unlatched logic inputs select the TC5xx oper-
ating phase. The A, B inputs are normally driven by a
microprocessor I/O port or external logic.
Table 1. Internal Analog Gate Status
Internal Analog Gate Status
Conversion Phase
SWI
SW
+
RI
SW
RI
SWZ
SWR
SW1
SWIZ
Auto-Zero (A = 0, B = 1)
Closed
Closed
Closed
Input Signal Integration
Closed
(A = 1, B = 0)
Reference Voltage
Closed*
Closed
Deintegration (A =1, B= 1)
Integrator Output Zero
Closed
Closed
Closed
(A = 0, B = 0)
*Assumes a positive polarity input signal. SW–RI would be closed for a negative input signal.
PRECISION ANALOG FRONT ENDS
TC500
TC500A
TC510
TC514


Codice articolo simile - TC510COG

Produttore elettroniciIl numero della parteScheda tecnicaSpiegazioni elettronici
logo
Microchip Technology
TC510COG MICROCHIP-TC510COG Datasheet
565Kb / 28P
   Precision Analog Front Ends
2002
TC510COG MICROCHIP-TC510COG Datasheet
653Kb / 34P
   Precision Analog Front Ends
2006
TC510COG MICROCHIP-TC510COG Datasheet
588Kb / 38P
   Precision Analog Front Ends with Dual Slope ADC
2008
TC510COG713 MICROCHIP-TC510COG713 Datasheet
653Kb / 34P
   Precision Analog Front Ends
2006
TC510COG713 MICROCHIP-TC510COG713 Datasheet
588Kb / 38P
   Precision Analog Front Ends with Dual Slope ADC
2008
More results

Descrizione simile - TC510COG

Produttore elettroniciIl numero della parteScheda tecnicaSpiegazioni elettronici
logo
Microchip Technology
TC500 MICROCHIP-TC500_06 Datasheet
653Kb / 34P
   Precision Analog Front Ends
2006
TC500 MICROCHIP-TC500 Datasheet
565Kb / 28P
   Precision Analog Front Ends
2002
TC500 MICROCHIP-TC500_08 Datasheet
588Kb / 38P
   Precision Analog Front Ends with Dual Slope ADC
2008
logo
Analog Devices
AD1018 AD-AD1018 Datasheet
72Kb / 2P
   High Precision Analog Front End
AD8450 AD-AD8450_17 Datasheet
1Mb / 42P
   Precision Analog Front End and Controller
AD8452 AD-AD8452 Datasheet
743Kb / 35P
   Precision Integrated Analog Front End, Controller
ADPD105 AD-ADPD105 Datasheet
884Kb / 66P
   Photometric Front Ends
ADPD1080 AD-ADPD1080 Datasheet
1Mb / 74P
   Photometric Front Ends
AD1030 AD-AD1030 Datasheet
78Kb / 2P
   High Precision Analog Front End with TEC/PMIC
Rev. Sp0
logo
STMicroelectronics
TDA7521 STMICROELECTRONICS-TDA7521 Datasheet
95Kb / 11P
   Analog Front End
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


Scheda tecnica Scarica

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEETIT.COM
Lei ha avuto il aiuto da alldatasheet?  [ DONATE ] 

Di alldatasheet   |   Richest di pubblicita   |   contatti   |   Privacy Policy   |   scambio Link   |   Ricerca produttore
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com