MC34713 datasheet(11/23 Pages) FREESCALE

Il numero della parte	MC34713

Spiegazioni elettronici	5.0 A 1.0 MHz Fully Integrated Single Switch-Mode Power Supply

Download	23 Pages

Scroll/Zoom	100%

Produttore elettronici	FREESCALE [Freescale Semiconductor, Inc]

Homepage	http://www.freescale.com

Logo

11 / 23 page

Analog Integrated Circuit Device Data

Freescale Semiconductor

11

34713

FUNCTIONAL DESCRIPTION

FUNCTIONAL INTERNAL BLOCK DESCRIPTION

enhance the gate of the high side Power MOSFET during

switching.

SHUTDOWN INPUT (SD)

If this pin is tied to the GND pin, the device will be in

Shutdown mode. If left unconnected or tied to the VIN pin, the

device will be in Normal mode. The pin has an internal pull-

up of 1.5 M

Ω.

POWER GOOD OUTPUT SIGNAL (PG)

This is an active low open drain output that is used to

report the status of the device to a host. This output activates

after a successful power up sequence and stays active as

long as the device is in normal operation and is not

experiencing any faults. This output activates after a 10 ms

delay and must be pulled up by an external resistor to a

supply voltage (e.g., VIN).

FUNCTIONAL INTERNAL BLOCK DESCRIPTION

Figure 4. 34713 Block Diagram

INTERNAL BIAS CIRCUITS

This block contains all circuits that provide the necessary

supply voltages and bias currents for the internal circuitry. It

consists of:

• Internal voltage supply regulator: This regulator

supplies the VDDI voltage that is used to drive the digital/

analog internal circuits. It is equipped with a Power-On-

Reset (POR) circuit that watches for the right regulation

levels. External filtering is needed on the VDDI pin. This

block will turn off during the shutdown mode.

• Internal bandgap reference voltage: This supplies the

reference voltage to some of the internal circuitry.

• Bias circuit: This block generates the bias currents

necessary to run all of the blocks in the IC.

SYSTEM CONTROL AND LOGIC

This block is the brain of the IC where the device

processes data and reacts to it. Based on the status of the SD

pin, the system control reacts accordingly and orders the

device into the right status. It also takes inputs from all of the

monitoring/protection circuits and initiates power up or power

down commands. It communicates with the buck converter to

manage the switching operation and protects it against any

faults.

OSCILLATOR

This block generates the clock cycles necessary to run the

IC digital blocks. It also generates the buck converter

switching frequency. The switching frequency has a default

value of 1.0 MHz and can be programmed by connecting a

resistor divider to the FREQ pin, between VDDI and GND

pins (See Figure 1).

PROTECTION FUNCTIONS

This block contains the following circuits:

• Over-current limit and short-circuit detection: This block

monitors the output of the buck converter for over

current conditions and short-circuit events and alerts

the system control for further command.

• Thermal limit detection: This block monitors the

temperature of the device for overheating events. If the

temperature rises above the thermal shutdown

MC34713 - Functional Block Diagram

Internal Bias Circuits

System Control and Logic

Oscillator

Protection Functions

Control and

Supervisory Functions

Tracking and Sequencing

Buck Converter

Codice articolo simile - MC34713

Produttore elettronici	Il numero della parte	Scheda tecnica	Spiegazioni elettronici
Freescale Semiconductor...	MC34713EP	510Kb / 21P	5.0 A 1.0MHz Fully Integrated Single Switch-Mode Power Supply
Freescale Semiconductor...	MC34713EPR2	510Kb / 21P	5.0 A 1.0MHz Fully Integrated Single Switch-Mode Power Supply

More results

Descrizione simile - MC34713

Produttore elettronici	Il numero della parte	Scheda tecnica	Spiegazioni elettronici
Freescale Semiconductor...	MC34717	778Kb / 28P	5.0 A 1.0 MHz Fully Integrated Dual Switch-Mode Power Supply
Freescale Semiconductor...	34717	651Kb / 25P	5.0 A 1.0 MHz Fully Integrated Dual Switch-Mode Dual Switch-Mode Power Supply
NXP Semiconductors	KT34717UG	1Mb / 20P	Using the 5.0 A 1.0 MHz Fully Integrated Dual Switch-Mode Power Supply Rev. 3.0, 1/2009
Freescale Semiconductor...	34713	510Kb / 21P	5.0 A 1.0MHz Fully Integrated Single Switch-Mode Power Supply
	MC34712	547Kb / 24P	3.0 A 1.0 MHz Fully Integrated DDR Switch-Mode Power Supply
	MC34164-3	477Kb / 23P	3.0 A 1.0 MHz Fully Integrated DDR Switch-Mode Power Supply
NXP Semiconductors	KT34712UG	2Mb / 16P	Using the 3.0 A 1.0 MHz Fully Integrated DDR Switch-Mode Power Supply Rev. 4.0, 1/2009
NXP Semiconductors	KT34713UG	2Mb / 18P	Using the 5.0A 1.0MHz Fully Integrated Single Switch-Mode Power Supply Rev. 4.0, 1/2009
Freescale Semiconductor...	MC34716	772Kb / 27P	1.0 MHz Dual Switch-Mode DDR Power Supply
Freescale Semiconductor...	34716	664Kb / 25P	1.0 MHz Dual Switch-Mode DDR Power Supply

More results

MC34713 Scheda tecnica(PDF) 11 Page - Freescale Semiconductor, Inc

MC34713 Scheda tecnica(HTML) 11 Page - Freescale Semiconductor, Inc

Codice articolo simile - MC34713

Descrizione simile - MC34713

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

Scheda tecnica Scarica

Link URL