Motore di ricerca datesheet componenti elettronici |
|
L6995D Scheda tecnica(PDF) 9 Page - STMicroelectronics |
|
L6995D Scheda tecnica(HTML) 9 Page - STMicroelectronics |
9 / 25 page 9/25 L6995 ductor value is, the smaller the threshold is. On the other hand, the bigger the inductor value is, the slower the transient response is. In PFM mode the frequency changes, with the output current changing, more than in PWM mode; in fact if the output current increase, the output voltage decreases more quickly; so the successive turn-on arrives before, increasing the switching frequency. The PFM waveforms may appear more noisy and asynchronous than normal operation, but this is normal behaviour mainly due to the very low load. If the PFM is not compatible with the application it can be disabled connecting to VCC the NOSKIP pin. 1.4 Softstart If the supply voltages are already applied, the SHDN pin gives the start-up. The system starts with the high side MOSFET off and the low side MOSFET on. After the SHDN pin is turned on the SS pin voltage begins to in- crease and the system starts to switch. The softstart is realized by gradually increasing the current limit thresh- old to avoid output overvoltage. The active soft start range for the VSS voltage (where the output current limit increase linearly) starts from 0.6V to 1.5V. In this range an internal current source (5 µA Typ) charges the ca- pacitor on the SS pin; the reference current (for the current limit comparator) forced through ILIM pin is propor- tional to SS pin voltage and it saturates at 5 µA (Typ.) when SS voltage is close to 1.5V and the maximum current limit is active. Undervoltage protection is disabled until SS pin voltage reaches 1.5V; instead the overvoltage is always present (see figure 5). Once the SS pin voltage reaches the 1.5V value, the voltage on SS pin doesn't impact the system operation anymore. If the SHDN pin is turned on before the supplies, the correct start-up sequence is the following: first turn-on the power section and after the logic section (VCC pin). Figure 5. Soft -Start Diagram Because the system implements the soft start controlling the inductor current, the soft start capacitor selection is function of the output capacitance, the current limit and the soft start active range ( ∆VSS). In order to select the softstart capacitor it must be imposed that the output voltage reaches the final value before the soft start voltage reaches the under voltage value (1.5V). In other words the output voltage charging time has to be lower than the uvp time. The UVP time is given by: Eq 7 In order to calculate the output volatge chargin time it should be calculated, before, the output volatrge function versus time. This function can be calculated from the inductor current function; the inductor current function can Time Time 0.6V Maximum current limit Soft-start active range 5 µA 4.1V 1.5V Ilim current Vss T uv p CSS () V uvp Iss ------------ C SS ⋅ = |
Codice articolo simile - L6995D |
|
Descrizione simile - L6995D |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |