Motore di ricerca datesheet componenti elettronici |
|
AMC3301-Q1 Scheda tecnica(PDF) 21 Page - Texas Instruments |
|
|
AMC3301-Q1 Scheda tecnica(HTML) 21 Page - Texas Instruments |
21 / 37 page -2.567 V VOUTN VOUTP Figure 7-5. Typical Failsafe Output of the AMC3301-Q1 7.3.4 Isolated DC/DC Converter The AMC3301-Q1 offers a fully integrated isolated DC/DC converter stage that includes following components illustrated in Section 7.2: • Low-dropout regulator (LDO) on the primary side to stabilize the supply voltage VDD that drives the primary side of the converter • Primary full-bridge inverter and drivers • Laminate-based, air-core transformer for high immunity to magnetic fields • Secondary full-bridge rectifier • Secondary LDO to stabilize the output voltage of the DC/DC converter for high analog performance of the signal path The DC/DC converter uses a spread-spectrum clock generation technique to reduce the spectral density of the electromagnetic radiation. The resonator frequency is synchronized to the operation of the ΔΣ modulator to minimize the interference with data transmission and support the high analog performance of the device. The architecture of the DC/DC converter is optimized to drive the high-side circuitry of the AMC3301-Q1 and can source up to IH of additional DC current for an optional auxiliary circuit such as an active filter, pre-amplifier or comparator. IH is specified in the Electrical Characteristics table in Section 6 as a DC, non-switching current. 7.3.5 Diagnostic Output The open-drain DIAG pin can be monitored to confirm the device is operational, and the output voltage is valid. During power-up, the DIAG pin is actively held low until the high-side supply is in regulation and the device operates properly. During normal operation the DIAG pin is in high-impedance (HiZ) state and pulled high through an external pull-up resistor. The DIAG pin is actively pulled low if: • The low-side does not receive data from the high-side (for example, because of a loss of power on the high- side). The amplifier outputs are driven to negative full-scale. • The high-side DC/DC output voltage (DCDC_OUT) or the high-side LDO output voltage (HLDO_OUT) drop below their respective undervoltage detection thresholds (brown-out). In this case, the low-side may still receive data from the high-side but the data may not be valid. The amplifier outputs are driven to negative full-scale. During normal operation, the DIAG pin is in a high-impedance state. Connect the DIAG pin to a pullup supply through a resistor or leave open if not used. www.ti.com AMC3301-Q1 SBASA73 – JULY 2020 Copyright © 2020 Texas Instruments Incorporated Submit Document Feedback 21 Product Folder Links: AMC3301-Q1 |
Codice articolo simile - AMC3301-Q1 |
|
Descrizione simile - AMC3301-Q1 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |