Motore di ricerca datesheet componenti elettronici |
|
9ZXL1231 Scheda tecnica(PDF) 8 Page - Integrated Device Technology |
|
9ZXL1231 Scheda tecnica(HTML) 8 Page - Integrated Device Technology |
8 / 18 page 12-OUTPUT DB1200ZL 8 REVISION J 05/25/16 9ZXL1231 DATASHEET Electrical Characteristics–DIF Low Power HCSL Outputs Electrical Characteristics–Current Consumption TAMB = TCOM or TIND, unless noted., Supply Voltages per normal operation conditions, See Test Loads for Loading Conditions PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS NOTES TAMB = TCOM, Scope averaging on 1.5 3.3 4 V/ns 1,2,3 TAMB = TIND Scope averaging on 1.5 3.1 4.5 V/ns 1,2,3 Slew rate matching ΔdV/dt Slew rate matching, Scope averaging on 7 20 % 1,2,4 Voltage High VHigh 660 778 850 Voltage Low VLow -150 0 150 Max Voltage Vmax 868 1150 Min Voltage Vmin -300 -64 Crossing Voltage (abs) Vcross_abs Scope averaging off 250 430 550 mV 1,5 Crossing Voltage (var) Δ-Vcross Scope averaging off 17 140 mV 1,6 2 Measured from differential waveform 7 At default SMBus settings. Slew rate dV/dt Statistical measurement on single-ended signal using oscilloscope math function. (Scope averaging on) mV Measurement on single ended signal using absolute value. (Scope averaging off) mV 1Guaranteed by design and characterization, not 100% tested in production. 3 Slew rate is measured through the Vswing voltage range centered around differential 0V. This results in a +/-150mV window around differential 0V. 4 Matching applies to rising edge rate for Clock and falling edge rate for Clock#. It is measured using a +/-75mV window centered on the average cross point where Clock rising meets Clock# falling. The median cross point is used to calculate the voltage thresholds the oscilloscope is to use for the edge rate calculations. 5 Vcross is defined as voltage where Clock = Clock# measured on a component test board and only applies to the differential rising edge (i.e. Clock rising and Clock# falling). 6 The total variation of all Vcross measurements in any particular system. Note that this is a subset of Vcross_min/max (Vcross absolute) allowed. The intent is to limit Vcross induced modulation by setting Δ-Vcross to be smaller than Vcross absolute. TAMB = TCOM or TIND, unless noted., Supply Voltages per normal operation conditions, See Test Loads for Loading Conditions PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS NOTES VDDA, PLL Mode@100MHz 18 20 mA 1 VDDA, PLL Bypass Mode@100MHz 6 10 mA 1 IDD All other VDD pins 16 25 mA IDDIO VDDIO for DIF outputs, if applicable 91 110 mA VDDA, PLL Mode@100MHz 3 5 mA 1 VDDA, PLL Bypass Mode@100MHz 3 5 mA 1 IDD All other VDD pins 0.01 1 mA IDDIO VDDIO for DIF outputs, if applicable 0.01 0.3 mA 1. Includes VDDR if applicable Operating Supply Current IDDA Power Down Current IDDA |
Codice articolo simile - 9ZXL1231 |
|
Descrizione simile - 9ZXL1231 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |