Motore di ricerca datesheet componenti elettronici |
|
I1505RU Scheda tecnica(PDF) 2 Page - MicroPower Direct, LLC |
|
I1505RU Scheda tecnica(HTML) 2 Page - MicroPower Direct, LLC |
2 / 2 page Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” on the top of the unit Model Number Input Output Over Voltage Protection (VDC) Efficiency (%, Typ) Capacitive Load (µF Max) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min) Nominal Range Full-Load No-Load I1501RU 24 9.0 - 36.0 647 15 3.3 4,000 0.0 3.9 86 1,000 3,000 I1502RU 24 9.0 - 36.0 727 15 5.0 3,000 0.0 6.2 87 1,000 4,000 I1503RU 24 9.0 - 36.0 747 15 12.0 1,300 0.0 15.0 88 330 4,000 I1504RU 24 9.0 - 36.0 710 15 15.0 1,000 0.0 18.0 89 220 4,000 I1505RU 24 9.0 - 36.0 744 15 ±5.0 ±1,500 ±0.0 ±6.2 85 ±470 4,000 I1506RU 24 9.0 - 36.0 718 15 ±12.0 ±625 ±0.0 ±15.0 88 ±220 4,000 I1507RU 24 9.0 - 36.0 710 15 ±15.0 ±500 ±0.0 ±18.0 89 ±100 4,000 I1511RU 48 18.0 - 75.0 331 10 3.3 4,000 0.0 3.9 84 1,000 1,500 I1512RU 48 18.0 - 75.0 368 10 5.0 3,000 0.0 6.2 86 1,000 2,000 I1513RU 48 18.0 - 75.0 378 10 12.0 1,300 0.0 15.0 87 330 2,000 I1514RU 48 18.0 - 75.0 360 10 15.0 1,000 0.0 18.0 88 220 2,000 I1515RU 48 18.0 - 75.0 376 10 ±5.0 ±1,500 ±0.0 ±6.2 84 ±470 2,000 I1516RU 48 18.0 - 75.0 363 10 ±12.0 ±625 ±0.0 ±15.0 87 ±220 2,000 I1517RU 48 18.0 - 75.0 359 10 ±15.0 ±500 ±0.0 ±18.0 88 ±100 2,000 Pin Single Dual 1 +Vin +Vin 2 -Vin -Vin 3 Control Control 4 +Vout +Vout 5 Trim Common 6 -Vout -Vout Derating Curve Notes: 1. Output load regulation is specified for a load change of 0% to 100%. 2. When measuring output ripple, it is recommended that an external ceramic capacitor (approx 0.1 µF) be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 3. Transient recovery is measured to within a 1% error band for a 25% load step change of 75% to 50% to 25%. 4. All models meet the EMC requirements of EN55022 Class A & EN61000-4-2/3/4/5/6/8 Criteria A; with the minimum addition of external components. Contact the factory for recommended filter capacitor values. 5. Operation at no-load will not damage the unit, but they may not meet all specifications. 6. The On/Off Control input (Pin 3) is refer- enced to -Vin (Pin 1). If it is not used, the control pin should be left open. Shorting Pin 3 and Pin 2 will shut the unit off. The off idle current is typically 5 mA. 7. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. www.micropowerdirect.com The output voltage on single output models may be adjusted by approximately ±10%. To do so, external trim resistors should connected as shown above. External Trim Model Selection Guide Mechanical Dimensions Pin Connections MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com Min Max On 3.0 VDC 12.0 VDC Off 0.0 VDC 1.2 VDC |
Codice articolo simile - I1505RU |
|
Descrizione simile - I1505RU |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |