CAR2012TEBXXZ01A datasheet(11/20 Pages) LINEAGEPOWER

Il numero della parte	CAR2012TEBXXZ01A

Spiegazioni elettronici	Universal input with PFC Constant power characteristic 2 front panel LEDs: 1-input;2

Download	20 Pages

Scroll/Zoom	100%

Produttore elettronici	LINEAGEPOWER [Lineage Power Corporation]

Homepage	http://www.lineagepower.com

Logo

11 / 20 page

GE

Data Sheet

CAR2012TE series rectifier

Input: 85Vac to 264Vac; Output: 12 Vdc @ 2000W; 3.3Vdc or 5 Vdc @ 4A

February 9, 2014

Page 11

The Linear Data Format is a two byte value with an 11-bit,

two’s complement mantissa and a 5-bit, two’s complement

exponent or scaling factor, its format is shown below.

Data Byte High

Data Byte Low

Bit 7

6

5

4

3

2

1

0

7

6

5

4

3

2

1

0

Exponent (E)

Mantissa (M)

The relationship between the Mantissa, Exponent, and Actual

Value (V) is given by the following equation:

E

M

V

2





Where:

V is the value

M is the 11-bit, two’s complement mantissa

E is the 5-bit, two’s complement exponent

Standard features

Command

Comments

ON_OFF_CONFIG

Both the CNTL pin, enabling or disabling

the output, and the OPERATION command

are supported. Other options are not

supported.

Vout_OV_fault_response

Only latched (0x80) is supported

CAPABILITY

400KHz, SMBALERT

PMBus revision

1.2

PMBusTM Command set:

Non-supported commands are annunciated.

Command

Hex

Code

Data

Byte

Function

Operation

0x01

1

Output ON/OFF

ON_OFF_config

0x02

1

09, output ON default

Clear_faults

0x03

0

Clear Status

Write_protect

0x10

1

Write control

Restore_default_all

0x12

0

Reset defaults

Store_default_code

0x13

1

Change default state

Vout_mode

0x20

1

Vout constants

Vout_command

0x21

2

Set Vout

Fan_command_1

0x3B

2

Set fan speed in %

Vout_OV_fault_limit

0x40

2

Set OV fault limit

Vout_OV_warn_limit

0x42

2

Set OV warn limit

Iout_OC_fault_limit

0x46

2

Iout_OC_fault_response4

0x47

1

Latch or hiccup

Iout_OC_warn_limit

0x4A

2

Set OC warn limit

OT_fault_limit

0x4F

2

OT_fault_response5

0x50

1

Latch or hiccup

OT_warn_limit

0x51

2

Set OT warn limit

Status_byte

0x78

1

Status_word

0x79

2

Status_Vout

0x7A

1

Status_Iout

0x7B

1

Status_input

0x7C

1

Status_temperature

0x7D

1

Status_CML

0x7E

1

Status_fan_1_2

0x81

1

Read_Iin

0x89

2

4

Only latched (0xC0) or hiccup (0xF8) are supported

5

Only latched (0x80) or restart (0xC0) are supported

Command

Hex

Code

Data

Byte

Function

Read_Vout

0x8B

2

Read_Iout

0x8C

2

Read_temperature

0x8D

2

Read_fan_speed_1

0x90

2

Read_fan_speed_2

0x91

2

Read_Pin

0x97

2

Mfr_ID

0x99

5

Mfr_model

0x9A

16

CAR2012TEXXXZ01A

Mfr_serial

0x9E

15

01KZ51018193xxx

Read_Std_Parameters

0xD0

10

Read_Status_State

0xD1

2

Read_Alarm_State

0xD2

2

Read_fan_speed

0xD3

4

Read_Input_string

0xD4

2

Read_mfr_rev

0xD5

4

Read_Run_Timer

0xD6

3

EEPROM_record

0xD9

64

Test Function

0xDF

1

Command Descriptions

Operation (0x01) : By default the Power supply is turned ON

at power up as long as Power ON/OFF signal pin is active HI.

The Operation command is used to turn the Power Supply ON

or OFF via the PMBus. The data byte below follows the

OPERATION command.

FUNCTION

DATA BYTE

Unit ON

80

Unit OFF

00

To RESET the power supply cycle the power supply OFF, wait

at least 2 seconds, and then turn back ON. All alarms and

shutdowns are cleared during a restart.

Clear_faults (0x03): This command clears all STATUS and

FAULT registers and resets the SMBAlert# line.

If a fault still persists after the issuance of the clear_faults

command the specific registers indicating the fault are reset

and the SMBAlert# line is activated again.

WRITE_PROTECT register (0x10): Used to control writing to

the PMBus device. The intent of this command is to provide

protection against accidental changes. All supported

command parameters may have their parameters read,

regardless of the write_protect settings. The default setting of

this register is disable_all_writes except write_protect 0x80h.

FUNCTION

DATA BYTE

Enable all writes

00

Disable all writes except write_protect

80

Disable all writes except write_protect and

OPERATION

40

Restore_Default_All (0x12): Restores all register values and

responses to the default parameters set in the power supply.

Codice articolo simile - CAR2012TEBXXZ01A

Produttore elettronici	Il numero della parte	Scheda tecnica	Spiegazioni elettronici
Riedon Powertron	CAR2010	251Kb / 1P	Thin Film Precisionion Chip Resistor
	CAR2010	168Kb / 2P	Thin Film Precision Chip Resistor
	CAR2010	145Kb / 3P	CAR Series

More results

Descrizione simile - CAR2012TEBXXZ01A

Produttore elettronici	Il numero della parte	Scheda tecnica	Spiegazioni elettronici
Lineage Power Corporati...	CAR1248TN	266Kb / 8P	Universal input with PFC Constant power characteristic 3 front panel LEDs: 1-input;2-output; 3 - fault
	CAR1248FP	264Kb / 11P	Universal input with PFC Constant power characteristic 3 front panel LEDs: 1-input;2-output; 3 - fault
	CAR2024FP	261Kb / 7P	Universal input with PFC Constant power characteristic front panel LEDs: input, output, fault
	CAR1612FP	293Kb / 7P	Universal input with PFC Constant power characteristic 2 front panel LED 1-input LED 2-[output, fault, over temp]
HITRON ELECTRONICS CORP...	HVP950	129Kb / 2P	UNIVERSAL INPUT HARMONIC CORRECTION(PFC)
	HEMP252G	84Kb / 2P	UNIVERSAL INPUT HARMONIC CORRECTION (PFC)
	HEMP250G	84Kb / 2P	UNIVERSAL INPUT HARMONIC CORRECTION (PFC)
	HEMP150G	54Kb / 2P	UNIVERSAL INPUT HARMONIC CORRECTION (PFC)
	HIMP151	997Kb / 2P	UNIVERSAL INPUT HARMONIC CORRECTION(PFC)
	HVP300	131Kb / 2P	UNIVERSAL INPUT HARMONIC CORRECTION(PFC)

More results

CAR2012TEBXXZ01A Scheda tecnica(PDF) 11 Page - Lineage Power Corporation

CAR2012TEBXXZ01A Scheda tecnica(HTML) 11 Page - Lineage Power Corporation

Codice articolo simile - CAR2012TEBXXZ01A

Descrizione simile - CAR2012TEBXXZ01A

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Scheda tecnica Scarica

Link URL