Motore di ricerca datesheet componenti elettronici |
|
ISL22414WMU10Z Scheda tecnica(PDF) 5 Page - Intersil Corporation |
|
ISL22414WMU10Z Scheda tecnica(HTML) 5 Page - Intersil Corporation |
5 / 16 page 5 FN6424.1 December 16, 2010 IV-SB V- Current (Standby) V- = -5.5V, VCC = +5.5V @ +85°C, SPI interface in standby state -2.5 -0.7 µA V- = -5.5V, VCC = +5.5V @ +125°C, SPI interface in standby state -4 -3 µA V- = -2.25V, VCC = +2.25V @ +85°C, SPI interface in standby state -1.5 -0.3 µA V- = -2.25V, VCC = +2.25V @ +125°C, SPI interface in standby state -3 -1 µA ISD VCC Current (Shutdown) VCC = +5.5V, V- = -5.5V @ +85°C, SPI interface in standby state 0.2 1.5 µA VCC = +5.5V, V- = -5.5V @ +125°C, SPI interface in standby state 12.5 µA VCC = +2.25V, V- = -2.25V @ +85°C, SPI interface in standby state 0.1 1 µA VCC = +2.25V, V- = -2.25V @ +125°C, SPI interface in standby state 0.5 2 µA IV-SD V- Current (Shutdown) V- = -5.5V, VCC = +5.5V @ +85°C, SPI interface in standby state -2.5 -0.7 µA V- = -5.5V, VCC = +5.5V @ +125°C, SPI interface in standby state -4 -3 µA V- = -2.25V, VCC = +2.25V @ +85°C, SPI interface in standby state -1.5 -0.3 µA V- = -2.25V, VCC = +2.25V @ +125°C, SPI interface in standby state -3 -1 µA ILkgDig Leakage Current, at Pins SCK, SDI, SDO and CS Voltage at pin from GND to VCC -0.5 0.5 µA tWRT DCP Wiper Response Time CS rising edge to wiper new position 1.5 µs tShdnRec DCP Recall Time From Shutdown Mode CS rising edge to wiper stored position and RH connection 1.5 µs Vpor Power-on Recall Voltage Minimum VCC at which memory recall occurs 1.9 2.1 V VccRamp VCC Ramp Rate 0.2 V/ms tD Power-up Delay VCC above Vpor, to DCP Initial Value Register recall completed, and SPI Interface in standby state 5 ms EEPROM SPECIFICATION EEPROM Endurance 1,000,000 Cycles EEPROM Retention Temperature T ≤ +55ºC 50 Years tWC (Note 16) Non-volatile Write Cycle Time 12 20 ms SERIAL INTERFACE SPECIFICATIONS VIL SCK, SDI, and CS Input Buffer LOW voltage -0.3 0.3*VCC V VIH SCK, SDI, and CS Input Buffer HIGH Voltage 0.7*VCC VCC+0.3 V Hysteresis SCK, SDI, and CS Input Buffer Hysteresis 0.05*VCC V VOL SDO Output Buffer LOW Voltage IOL = 4mA for Open Drain output, pull-up voltage Vpu = VCC 00.4 V Operating Specifications Over the recommended operating conditions unless otherwise specified. Boldface limits apply over the operating temperature range. (Continued) SYMBOL PARAMETER TEST CONDITIONS MIN (Note 18) TYP (Note 4) MAX (Note 18) UNIT ISL22414 |
Codice articolo simile - ISL22414WMU10Z |
|
Descrizione simile - ISL22414WMU10Z |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |