Motore di ricerca datesheet componenti elettronici |
|
AT90S2313 Scheda tecnica(PDF) 60 Page - ATMEL Corporation |
|
AT90S2313 Scheda tecnica(HTML) 60 Page - ATMEL Corporation |
60 / 92 page 60 AT90S2313 0839I–AVR–06/02 Memory Programming Program and Data Memory Lock Bits The AT90S2313 MCU provides two Lock bits that can be left unprogrammed (“1”)or can be programmed (“0”) to obtain the additional features listed in Table 21. The Lock bits can only be erased with the Chip Erase operation. Note: 1. In the Parallel mode, further programming of the Fuse bits are also disabled. Program the Fuse bits before programming the Lock bits. Fuse Bits The AT90S2313 has two Fuse bits: SPIEN and FSTRT. • When the SPIEN Fuse is programmed (“0”), Serial Program and Data Downloading is enabled. The default value is programmed (“0”). • When the FSTRT Fuse is programmed (“0”), the short start-up time is selected. The default value is unprogrammed (“1”). Parts with this bit pre-programmed (“0”)can be delivered on demand. The Fuse bits are not accessible in Serial Programming mode. The status of the fuses are not affected by Chip Erase. Signature Bytes All Atmel microcontrollers have a 3-byte signature code that identifies the device. This code can be read in both serial and parallel mode. The three bytes reside in a separate address space. For the AT90S2313 (1) they are: 1. $000: $1E (indicates manufactured by Atmel). 2. $001: $91 (indicates 2 Kb Flash memory). 3. $002: $01 (indicates AT90S2313 device when signature byte $001 is $91). Note: 1. When both Lock bits are programmed (Lock mode 3), the signature bytes cannot be read in serial mode. Reading the signature bytes will return: $00, $01 and $02. Programming the Flash and EEPROM Atmel’s AT90S2313 offers 2K bytes of In-System Reprogrammable Flash Program memory and 128 bytes of EEPROM Data memory. The AT90S2313 is shipped with the On-chip Flash Program and EEPROM Data mem- ory arrays in the erased state (i.e., contents = $FF) and ready to be programmed. This device supports a high-voltage (12V) Parallel Programming mode and a low-voltage Serial Programming mode. The +12V is used for programming enable only, and no cur- rent of significance is drawn by this pin. The Serial Programming mode provides a convenient way to download program and data into the AT90S2313 inside the user’s system. The program and EEPROM memory arrays in the AT90S2313 are programmed byte- by-byte in either programming mode. For the EEPROM, an auto-erase cycle is provided Table 21. Lock Bit Protection Modes Memory Lock Bits Protection Type Mode LB1 LB2 1 1 1 No memory lock features enabled. 2 0 1 Further programming of the Flash and EEPROM is disabled. (1) 3 0 0 Same as mode 2, and verify is also disabled. |
Codice articolo simile - AT90S2313_02 |
|
Descrizione simile - AT90S2313_02 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |