Motore di ricerca datesheet componenti elettronici |
|
TPA2006D1DRBR Scheda tecnica(PDF) 9 Page - Texas Instruments |
|
|
TPA2006D1DRBR Scheda tecnica(HTML) 9 Page - Texas Instruments |
9 / 23 page www.ti.com APPLICATION INFORMATION FULLY DIFFERENTIAL AMPLIFIER Advantages of Fully Differential Amplifiers COMPONENT SELECTION TPA2006D1 SLOS498 – SEPTEMBER 2006 The TPA2006D1 is a fully differential amplifier with differential inputs and outputs. The fully differential amplifier consists of a differential amplifier and a common-mode amplifier. The differential amplifier ensures that the amplifier outputs a differential voltage on the output that is equal to the differential input times the gain. The common-mode feedback ensures that the common-mode voltage at the output is biased around VDD/2 regardless of the common-mode voltage at the input. The fully differential TPA2006D1 can still be used with a single-ended input; however, the TPA2006D1 should be used with differential inputs when in a noisy environment, like a wireless handset, to ensure maximum noise rejection. • Input-coupling capacitors not required: – The fully differential amplifier allows the inputs to be biased at voltage other than mid-supply. For example, if a codec has a mid-supply lower than the mid-supply of the TPA2006D1, the common-mode feedback circuit will adjust, and the TPA2006D1 outputs will still be biased at mid-supply of the TPA2006D1. The inputs of the TPA2006D1 can be biased from 0.5 V to VDD – 0.8 V. If the inputs are biased outside of that range, input-coupling capacitors are required. • Mid-supply bypass capacitor, C(BYPASS), not required: – The fully differential amplifier does not require a bypass capacitor. This is because any shift in the midsupply affects both positive and negative channels equally and cancels at the differential output. • Better RF-immunity: – GSM handsets save power by turning on and shutting off the RF transmitter at a rate of 217 Hz. The transmitted signal is picked-up on input and output traces. The fully differential amplifier cancels the signal much better than the typical audio amplifier. Figure 21 shows the TPA2006D1 typical schematic with differential inputs and Figure 22 shows the TPA2006D1 with differential inputs and input capacitors, and Figure 23 shows the TPA2006D1 with single-ended inputs. Differential inputs should be used whenever possible because the single-ended inputs are much more susceptible to noise. Table 1. Typical Component Values REF DES VALUE EIA SIZE MANUFACTURER PART NUMBER RI 150 k Ω (±0.5%) 0402 Panasonic ERJ2RHD154V CS 1 µF (+22%, -80%) 0402 Murata GRP155F50J105Z CI(1) 3.3 nF ( ±10%) 0201 Murata GRP033B10J332K (1) CI is only needed for single-ended input or if VICM is not between 0.5 V and VDD– 0.8 V. CI = 3.3 nF (with RI = 150 kΩ) gives a high-pass corner frequency of 321 Hz. 9 Submit Documentation Feedback |
Codice articolo simile - TPA2006D1DRBR |
|
Descrizione simile - TPA2006D1DRBR |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |