Motore di ricerca datesheet componenti elettronici |
|
LM150X08 Scheda tecnica(PDF) 7 Page - LG Semicon Co.,Ltd. |
|
LM150X08 Scheda tecnica(HTML) 7 Page - LG Semicon Co.,Ltd. |
7 / 28 page Product Specification 7 / 28 LM150X08 Liquid Crystal Display Ver. 0.0 Nov. 13, 2003 MIKO Components AB Tel: +46 (0)8 531 939 00 Fax: +46 (0)8 531 939 39 www.miko.se info@miko.se Table 2_2. ELECTRICAL CHARACTERISTICS 6 Watt 9.86 8.96 PBL Power Consumption 1, 5 Min 3 Ts Discharge Stabilization Time at 0 °C at 25 °C V RMS 1,100 4 kHz 80 60 45 fBL Operating Frequency 1, 3 Vs Established Starting Voltage V RMS 850 1, 2 V RMS 650(3mA) 560(8mA) 550(9mA) VBL Operating Voltage 1 mARMS 9.0 8.0 3.0 IBL Operating Current LAMP : 1, 7 Hrs 40,000 Life Time Parameter Symbol Max Typ Min Notes Unit Values Note : The design of the inverter must have specifications for the lamp in LCD Assembly. The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced by the characteristics of the DC-AC inverter. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. When you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter (no lighting, flicker, etc) never occurs. When you confirm it, the LCD – Assembly should be operated in the same condition as installed in you instrument. ? Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to a conducting tape, TFT-LCD Module has a low luminance and the inverter has abnormal action. Because leakage current is occurred between lamp wire and conducting tape. 1. Specified values are for a single lamp. 2. Operating voltage is measured at 25 ? 2°C. The variance of the voltage is ? 10%. 3. The voltage above V S should be applied to the lamps for more than 1 second for start-up. (Inverter open voltage must be more than lamp starting voltage.) Otherwise, the lamps may not be turned on. The used lamp current is the lamp typical current. 4. Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may cause beat on the display. Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference. 5. Let ’s define the brightness of the lamp after being lighted for 5 minutes as 100%. T S is the time required for the brightness of the center of the lamp to be not less than 95%. 6. The lamp power consumption shown above does not include loss of external inverter. The used lamp current is the lamp typical current. (P BL = VBL x IBL xNLamp ) 7. The life is determined as the time at which brightness of the lamp is 50% compared to that of initial value at the typical lamp current on condition of continuous operating at 25 ? 2°C. |
Codice articolo simile - LM150X08 |
|
Descrizione simile - LM150X08 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |