MOTOROLA

SEMICONDUCTOR TECHNICAL DATA

2–296

REV 5

3/93

Dual 3-Input 3-Output NOR

Gate

The MC10H211 is designed to drive up to six transmission lines simultan–

eously. The multiple outputs of this device also allow the wire “OR”–ing of

several levels of gating for minimization of gate and package count.

The ability to control three parallel lines with minimum propagation delay

from a single point makes the MC10H211 particularly useful in clock distribution

applications where minimum clock skew is desired.

• Propagation Delay, 1.0 ns Typical

• Power Dissipation, 160 mW Typical

• Improved Noise Margin 150 mV (Over Operating Voltage and

Temperature Range)

• Voltage Compensated

• MECL 10K–Compatible

MAXIMUM RATINGS

Characteristic

Symbol

Rating

Unit

Power Supply (VCC = 0)

VEE

–8.0 to 0

Vdc

Input Voltage (VCC = 0)

VI

0 to VEE

Vdc

Output Current — Continuous

— Surge

Iout

50

100

mA

Operating Temperature Range

TA

0 to +75

°C

Storage Temperature Range — Plastic

— Ceramic

Tstg

–55 to +150

–55 to +165

°C

°C

ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)

0

°

25

°

75

°

Characteristic

Symbol

Min

Max

Min

Max

Min

Max

Unit

Power Supply Current

IE

—

42

—

38

—

42

mA

Input Current High

IinH

—

720

—

450

—

450

µA

Input Current Low

IinL

0.5

—

0.5

—

0.3

—

µA

High Output Voltage

VOH

–1.02

–0.84

–0.98

–0.81

–0.92

–0.735

Vdc

Low Output Voltage

VOL

–1.95

–1.63

–1.95

–1.63

–1.95

–1.60

Vdc

High Input Voltage

VIH

–1.17

–0.84

–1.13

–0.81

–1.07

–0.735

Vdc

Low Input Voltage

VIL

–1.95

–1.48

–1.95

–1.48

–1.95

–1.45

Vdc

AC PARAMETERS

Propagation Delay

tpd

0.7

1.6

0.7

1.6

0.7

1.7

ns

Rise Time

tr

0.9

2.0

0.9

2.2

0.9

2.4

ns

Fall Time

tf

0.9

2.0

0.9

2.2

0.9

2.4

ns

NOTE:

Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,

after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed

circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated

through a 50–ohm resistor to –2.0 volts.

Note: If crosstalk is present, double bypass capacitor to 0.2

µF.

MC10H211

LOGIC DIAGRAM

DIP

PIN ASSIGNMENT

VCC1

AOUT

AOUT

AOUT

AIN

AIN

AIN

VEE

VCC2

VCC1

BOUT

BOUT

BOUT

BIN

BIN

BIN

16

15

14

13

12

11

10

9

1

2

3

4

5

6

7

8

VCC1 = PINS 1, 15

VCC2 = PIN 16

VEE = PIN 8

12

11

10

9

13

14

2

7

6

5

3

4

L SUFFIX

CERAMIC PACKAGE

CASE 620–10

P SUFFIX

PLASTIC PACKAGE

CASE 648–08

FN SUFFIX

PLCC

CASE 775–02

Pin assignment is for Dual–in–Line Package.

For PLCC pin assignment, see the Pin Conversion

Tables on page 6–11 of the Motorola MECL Data

Book (DL122/D).