Motore di ricerca datesheet componenti elettronici |
|
GD25LB32D Scheda tecnica(PDF) 31 Page - GigaDevice Semiconductor (Beijing) Inc. |
|
GD25LB32D Scheda tecnica(HTML) 31 Page - GigaDevice Semiconductor (Beijing) Inc. |
31 / 67 page 1.8V Uniform Sector Dual and Quad Serial Flash GD25LB32D 31 Figure15a. Page Program Sequence Diagram (QPI) CS# SCLK IO0 IO1 IO2 IO3 0 1 2 3 4 5 Command 02H 20 12 16 8 6 7 8 9 10 4 4 0 0 4 0 4 0 21 13 17 9 5 5 1 1 5 1 5 1 22 14 18 10 6 6 2 2 6 2 6 2 23 15 19 11 7 7 3 3 7 3 7 3 A23-16 A15-8 A7-0 11 12 13 Byte1 Byte2 4 0 4 0 5 1 5 1 6 2 6 2 7 3 7 3 Byte3 Byte255 Byte256 7.16. Quad Page Program (32H) The Quad Page Program command is for programming the memory using four pins: IO0, IO1, IO2, and IO3. A Write Enable (WREN) command must previously have been executed to set the Write Enable Latch (WEL) bit before sending the Page Program command. The quad Page Program command is entered by driving CS# Low, followed by the command code (32H), three address bytes and at least one data byte on IO pins. The command sequence is shown in Figure16. If more than 256 bytes are sent to the device, previously latched data are discarded and the last 256 data bytes are guaranteed to be programmed correctly within the same page. If less than 256 data bytes are sent to device, they are correctly programmed at the requested addresses without having any effects on the other bytes of the same page. CS# must be driven high after the eighth bit of the last data byte has been latched in; otherwise the Quad Page Program (PP) command is not executed. As soon as CS# is driven high, the self-timed Quad Page Program cycle (whose duration is tPP) is initiated. While the Quad Page Program cycle is in progress, the Status Register may be read to check the value of the Write In Progress (WIP) bit. The Write in Progress (WIP) bit is 1 during the self-timed Quad Page Program cycle, and is 0 when it is completed. At some unspecified time before the cycle is completed, the Write Enable Latch (WEL) bit is reset. A Quad Page Program command applied to a page which is protected by the Block Protect (BP4, BP3, BP2, BP1, and BP0) is not executed. |
Codice articolo simile - GD25LB32D |
|
Descrizione simile - GD25LB32D |
|
|
Link URL |
Privacy Policy |
ALLDATASHEETIT.COM |
Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |